0 votes
3k views

Hello Technicians, this is a follow up question, from my last question on this Thermador dishwasher.
I have checked all that was suggested from my last question on this product. Drain is clear and unobstructed. Wash arm spray nozzles are clear, detergent dispenser is working properly. Two things I have found ,when upper rack only is used and then you return to both racks the plunger that diverts water to the top rack sticks in the closed position and bottom spray arm does not work , I can take the spray arm off and take my finger and press the plunger down and the spray arm functions properly. I have also noticed the water in the tub is only 110 degrees. The flow through heaters do not come on and heat the water until about 30 minuets into the cycle, according to the service manual the dishwasher will pull 11 amps when The heaters are activated, the dishwasher pulls 1.5 amps for the first 25 to 30 minuets of both normal and heavy wash cycles. Can you advise me on how long into the cycle is normal for the heaters to begin operation and also the best way to stop the plunger from sticking. Any advise is appreciated.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

do you have any repair videos on this washer?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
12k views

I have a GE dishwasher and the Vent Cover keeps “Popping Off” and the is Vent Leaking . Is there a fix for this issue ?

0 votes
4k views

My GE washer will not drain all the water out of it.

0 votes
3k views

no water.

0 votes
3k views

My GE washer just starts then stops.

0 votes
2k views

lid will not lock on my GE washer.

0 votes
2k views

Will not turn on.

0 votes
3k views

My GE washer will not fill with water.

1 vote
3k views

Kenmore dryer 110.66912690

I have checked the dryer and all signs pointed a defective blower motor
I am looking for a disassembly video for this particular model and particularly for replacing the blower motor

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Washer will not run, Console displays error code

0 votes
3k views

water temp is wrong

0 votes
4k views

Will not fill with detergent

0 votes
4k views

Will not dispense ice, Ice water dripping in freezer

0 votes
5k views

Will not make ice or dispense water.

0 votes
2k views
  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

My Whirlpool refrigerator is not cold enough.

0 votes
4k views

My Whirlpool refrigerator is not cooling.

0 votes
3k views

Ice builds up on evaporator

0 votes
3k views

My Whirlpool refrigerator is not dispensing water or ice.

0 votes
2k views

My bottom freezer door gets stuck shut.

0 votes
4k views

My refrigerator will not produce ice.

0 votes
3k views

Freezer light will not come on in my Whirlpool refrigerator.

0 votes
4k views

Customer complains 1e code more than usual.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
10k views

Small left oven after a couple minutes of baking in any mode the clean light comes on steady and oven light Flashes three times. The cooling fan seem to be running fine from what I can hear and I looked at the big relay at the bottom of the oven for the small left oven that is having the problems and they look to be in perfect condition and all its connectors. Can I please have a diagnostic manual that will tell me what the flashes mean?

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
4k views

I just became a premium member just for situations like this.
Can you guide me to a video on how to replace the damper part # WR60X10062 ? I can’t find one?
Thanks
Dale Stoltz
Quick and Easy Appliance

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Customer complains of strange noise claiming to come from freezer section. (sounds like a jet)
I have yet to hear this after 3 visits to the home. Is this style of evaporator fan motor notorious for making noises like the older fan motors (WR60X10185), or should i be focused somewhere else? Any help of any kind is appreciated.
P.S. the fresh food fan has been changed out by GE.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

The customer had previous service for the ice maker freezing up and a new ice maker was installed by previous servicer. Based on customer complaint of needing to manually thaw the fill tube we replaced the water valve. Customer now reports continued icing up in the ice maker.

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
4k views

I AM TH NKING THIS MAY HAVE BEEN CAUSED BY CLOGGED UP VENT… OR POSSIBLY THE VENTED HOLES MAY ALSO BE CLOGGED OUTSIDE. NEED SOME IDEAS, BEFORE DIAGNOSING THIS MACHINE….

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

I have a washer that will not agitate proberly. I changed hull sensor and coupling assembly. Diagnostics comes up with no errors. Agitation is not enough to clean the clothes. What component controls the agitation power. Is it the gearbox? All other cycles work great. Spin works fine

  • Guest asked 8 years ago
  • last active 8 years ago
Showing 3241 - 3270 of 9k results