Repair Help

Fresh food section / refrigerator Is not defrosting and restricting the airflow with the giant block of snow. Ran the system through self diagnostic mode nothing came up but when I ran the sensor diagnostic out of the ten sensors it tested, sensor #7 failed.
Now here’s the issue, the whole system is a cluster of bunch of plastic parts
IS THERE A MAP OF THE TEMPETURE SENSORS so I can find #7 instead of finding all 10 and having to test manually?

(In Samsung category because wouldn’t find GE brand and unit compressor was Samsung)

Can I get the service manual for this model. I am getting a UE and LE code. I thought it was a bad strut so I replaced all 4. I did get it into dyagnostics and it went into a high speed spin with no issues but if you run a drain and spin it wil drain do a low speed spin then stop and repeat 3-4 times then the error code UE and LE come up.

The compressor, inverter board and main control board was changed. Before the unit was not cooling (compressor issue) and there was a audile beeping noise also compressor would try to start. NOW after everything has been changed out. There is a clicking noise and the fans will stop momentary and come back on. Also when that happens the temperature display in the top inside of refrigerator will dim. Like I noted, fans will stop and come back on, but the compressor will stay running until set temperature is reached. Please in any way possible. Thanks Ricky

My Maytag MVWX700XL2 washer starts before the spin cycle starts. Only error code was F9 E1. When it runs through diagnostic test, the spin works but not in normal cycle. Pumps out fine. Pulled everything apart. Cleaned inner drum and pump. No debris found, only some film and a little silt.

My maytag washer 4000 series will start spin once then the pump comes on to dump the water out and stay on . What can I do to fix that problem

My new speed queen TR3 washing machine does not have a spin only cycle. is there any way to trick it into just spinning?

My Maytag Series 3000 Washer keeps displaying error F21. I’ve cleaned the long drain behind the bottom front panel and also checked all the hoses and none of which are kinked or clogged. The washer will complete all cycles and drain like normal when empty, but will display F21 when filled with clothes. I’ve put a very small load in (2 shirts and a pair of jeans) to make sure it was draining properly and am still getting error F21. Help!

We have a Whirlpool LEB6300PW1 clothes dryer. Drum spins and air comes out the vent but with no heat. Is it worth fixing or should we buy a new one?

Washer making a loud surging rubbing noise on the spin cycle.

My Maytag MVWX700XL2 washer starts before the spin cycle starts. Only error code was F9 E1. When it runs through diagnostic test, the spin works but not in normal cycle. Pumps out fine. Pulled everything apart. Cleaned inner drum and pump. No debris found, only some film and a little silt.

My maytag washer 4000 series will start spin once then the pump comes on to dump the water out and stay on . What can I do to fix that problem. I have tried to unplug the unit to reset the board and it did not work.

Whirlpool washer doesn’t spin. Changed motor coupling and clutch.

My GE elec. dryer mod.# GFDR27OEHOWW when start button is pushed begins to time out but does not run, only single click sound is heard.already checked all three thermostats they are good.

This is not a quick fix the microwave problem is due to a bad door switch. There are three door switches on the interlock circuit and if any one of them goes bad the unit will not allow it to start. Most times when the switch goes bad it is typically the lower one that burns out or the upper one that burns out. When that happens the unit will not be allowed to start up and run. you would need to take that apart and check out all 3 switches on the interlock circuit.

My KitchenAid microwave convection oven turns on, lights up but carousel does not turn and food doesn’t cook. was working fine until i used what i thought was the timer for 60 minutes – turned out it was on for that length of time.

Our ice maker in the bottom freezer does not work. We also hear a crackling/clicking sound. We vacuumed the bottom really well but still no luck.

Frigidaire dishwasher not working. First it would not drain. Got all the water out with a shop vac and cleaned the drain. Went to test but not nothing happens. Lights come on and it switches over to washing but it’s quiet. No water to the dishwasher. Was thinking maybe float switch/relay.

I have an E24 code on my Bosch Dishwasher.

WHEN THE TEMPERATURE IS SET, IT VERY SLOW REACHING THE SET TEMPERATURE. AFTER REACHING THE SET TEMPERATURE, IT DROPS DOWN TO A LOW TEMPERATURE. SOMETIMES, ALL THE POWER SHUT DOWN, AT THE MIDDLE OF COOKING. THIS IS A DOUBLE OVEN. ALL THE POWER GET SHUT DOWN AT THE SAME TIME. IN BOTH THE UPPER AND LOWER OVEN.

I inadvertently put the microwave on for an hour thinking it was on the timer. It is dead now. Any ideas?

I have an Amana AFI2538AEB4 refridgerator. The control panel is not working. The power is good. The interior refridge light is on. If I press any button on the control panel every light and number lights up. So that means the control panel has power. Is there some type of reset?

Maytag MF12568AES refrigerator control panel not working. Yesterday came home and lights on control panel were out and it was just buzzing. I believe the fridge is working. We have had issue for past year with switching from water and ice so we have just left it on water. Which should I replace – control panel on back, control panel on front, or display panel. How can test to figure out which is bad. I unplugged the connector with three wires attached to control panel on the front and it lights up as normal but no water and cannot use any of the buttons.

will not go into spin cycle.

My washer is showing code F3 E1. I had a serviceman out less than 6 months ago for the same problem. What he replaced was I think the drum motor. I had already looked the code up and saw that it was a pressure switch but he said he didn’t think that was it. At any rate, how can I get the door to unlock? I need to get the clothes out, obviously. He will be back on Wednesday to repair again.

Everything I can actaully get it to go thru entire quick wash by allowing the hose to drain with lowering it to floor. It gets stopped on each part of cycle where it needs to drain so i lower hiose to plastic tub on floor and in minute or so it goes on to like rinse in spin. all the way to end. installed new pump.

My Maytag washer is very loud during spin.

I checked on this washer which at first had a lid lock issue. We replaced the lid lock and worked fine for a couple months. Afterwards, we went back out with the same error code and the lid lock tested fine which we were going to replace the control board. We went back out finding the error code is now gone but the F7E5 error code not pops up. We replaced the board and the same code popped up, we also replaced the shift actuator which did not change anything on the unit. Afterwards we went through each step on the test #3a finding no issues with the shifter or the wire harness. Is this something that could also be caused by the motor?

I have a dryer that will run 1 load and work fine then on the 2nd load just stops and the start button blinks. you can start it again but it will only run for 5 seconds or so and the start button will blink again. there are no error codes