Appliance Type: Dishwasher

This dishwasher has a new sump so it came with a new grommet. The diverter motor is leaking when the pump starts spraying. Any way of sealing this up? Or would it need a new diverter motor?

No power on display. Checked power coming in at the bottom of dishwasher terminal and there is 120 volts coming in. I’m thinking it’s the board but I want to make sure since I can’t find any service manual for this model. Thanks.

when you wash the dishes it gets to the rinse the unit just starts beeping and continues to beep? Have you heard of this problem and know what the the common problem for this unit is. There is a little water in the unit after the drawer is pulled out. Is this normal?

when it gets to the end to the end of the cycle the unit will still run. Evan over night

Fills but does not drain goes through cycle except for drain

Three days ago, I heard a noise after the washer completed its cycle. Upon inspection, I’ve discovered, the square-shaped motor on the bottom of the machine is running non-stop. It will only stop when the machine is unplugged. All other operation seems fine: e.g., dishes are getting cleaned, water is draining and there are no funny noises while the machine operates. Further, there are no blinking lights.

I cannot find anything online, including your videos, which describe the symptoms I’m observing. My only guess is whatever controls the motor is causing the problem – a stuck relay, or a bad board… I’m stuck and need help.

Thanks in advance.

The appliance is only run approximately every 2 weeks as there are only 2 of us seniors in the household. I made all the selections as normal and selected the start, closed the door immediately, and shortly afterward the light started flashing and the beeper comes on. I have canceled the program multiple times and re-selected different programs to see if made any difference, but the same results occurred once the door was shut. I have check all the filters to ensure they are clean. I do not have an electrical schematic to see if there are any other permissive interlocks that could be holding the start initiation sequence out.

The dishwasher appears to run well and fill and drain properly. I did notice that water was not hot during wash cycle. I could hear the spray arms rotating well. Is this dishwasher supposed to heat up the water. I need the manual or schematic for it. Thank you. I did check the filter screen and didn’t look that bad.

Looking for some info on this.

Customer gave no details of when the dishwasher gives the code, only that it reads the code: nE.

I need a service manual. I tried a service test holding power heavy and delicate and it displayed 15. My old manual only shows codes by less. Is it in flood mode? Maybe the sensor in the bottom? What does this sound like?

Tested element, reads good. Replaced control panel and main relay still no go? Tested heater connection on relay so means thermal fuse and wiring is fine, outlet a good 123v..? Goes through normal hour cycle but doesn’t dry..
Already asked question got French trouble shooting guide asking again

The customer showed me a video that sounded like the pump running with the door open. She said that it shows an error code often of 10 and last time it showed 30.
Where is the tech sheet hidden? I couldn’t find it behind the door panel or behind the toe plate.
I need a copy of it and the error codes and videos.

I CLOSE THE DOOR ON CUSTOMERS D/W AND BREAKER TRIPS WITH NO DRAMA RESET DISPLAY LIGHT AS NORMAL CLOSE DOOR BREAKER TRIPS IM NOT A NEWBIE BUT THIS PARTICULAR MODEL IS KIND OF COMPLICATED ANY HELP WOULD BE GREAT THANK YOU

At first it was draining while it was filling. Then after ordering the drain valve and pump it began working OK for a few months. Then the customer called back and said it wasn’t cleaning well again. I found it was out of position and tilted forward and I leveled it up. Now it is not cleaning well and the tech sheet was in the customers records and can’t be located. I need so pointers on this one. It is as hard a Bosh DW.

The Door switch is good and if I unplug the interface then plug it back in it will clear for 15 second but still won’t respont to any commands. The power has been turned off for several minutes and makes no difference.

The tech sheet does not show any error codes. Do the 3 blinking led’s mean any thing. IF so , what?
Is there a manual for this.

I replaced the control panel still getting power but no lights note turn on

Need service manual on this dishwasher. Has E 09 foult code and water tap2!12

HOW DO I TROUBLESHOOT THIS? I SUSPECT BAD WATER VALVE. NO WATER IN TUB AND COMING UP WITH U6 ERROR CODE. THANKS.

I’m having an error 7-1 and 6-2. I need to know what these codes mean. Please help

Hi,

I need to replace my waterwall vane motor and have ordered the motor (part number DD31-00013B). I watched the video on how to remove the motion assembly and waterwall but I’m not sure how to remove the old motor and install the new one. Does the old motor drive pin just slide out and then just slide the new motor in or is there a seal i need to replace?

I have a dishwasher that powers on and when you hit start it counts down lines go across the screen it sits for around 1 min and powers down any thoughts?

filling and draining at same time. leaking on floor

Water in unit not getting heated and not drying dishes, element not coming on.

I recently removed the pump and motor assembly from this dishwasher. Anyways the pump assembly that we got was the wrong one. Now I have the correct one but I don’t remember how to put the wires back properly. They all seem to have I think either two or three pin connections.
Can you provide me with a wire diagram, or something to help me put this pump assembly back without screwing it up. Thank you very much appreciate it

Customer complains that his dishwasher Silverware rack dosnt dry at all, but the rest is dry???

motor dose not stay on for full agitation for cleaning dishes or dissolve detergent.

A while back the dishwasher would not start. The START button would flash and the indicator light flashes amber. It also beeps three times waits for a while and beeps three more times. This repeats over and over.

My dishes are still wet after the drying cycle.
What else we need to check to identify symptoms