Appliance Type: Washer

Hello, My washer & dryer are located in the kitchen. I have no basement. I have a front load washer. the problem I’m having is when the washer drain the water drain in my kitchen sink.

The washer needs to be rebooted to power up. and will not need to be powered up if you push the power within 30 seconds. But after one minute you need to do a reboot. That is unplugging it. Do I need to replace the main control board or the touch control board?

Bill
Neighhood appliance
Bill8321@aol.com

Washer not draining or spinning, I got it into diagnostic mode and got it to drain, but still wont spin. Its reporting a 5A error. Not sure what to troubleshoot next.

My washer is stuck. The motor to drain stays on. It still runs with lid opened or closed.

WHEN WASHER IS POWERED UP THE DISPLAY SAYS THE DOOR IS LOCKED AND IT CONTINUOUSLY
UNLOCKS THE LATCH BUT IT IS ALREADY UNLOCKED.

I saw this model on the premium videos. The diagnostics say it is an out of balance condition. It spins fine with out clothes. The balance ring has fluid. The customers loads are fine. Your premium videos say replace the suspension rods but they seem fine. What route should I go. The service manual says replace the basket.

I HAVE NO CLUE.

Is there any information on this issue?

I have an LG washer-front load about 4 years old. I did a small load of throw rugs and when it was done, I found a lot of water had leaked out of the bottom of the washer and all over my basement. What is the problem and can I fix it myself?
PS – I started to open the knob behind the door on the front of the washer and a lot of water started to flow out.
Thanks

Looking for manual so I can figure out why machine will not go into spin mode. It’s a Kenmore washer model # 110.26002010
Thanks.

WP2209751

Our Whirlpool washer will not drain. We start a load, it fills and spins once then the alarm beeps incessantly. The “door locked” red light stays on, and even when trying to cycle “rinse and spin” or “drain and spin”, it will not do either. Nor will it finish a load. When the red light goes out and you try to open the door, water spills over.

I need a service manual for this model. Is the problem in the board?

I’m trying to connect a 3 prong cable to a maytag bravo. Both the green and white wires terminate at middle terminal. The ground wire seems to come from internal harness. Do I still need a jumper ground wire?

Our Maytag washing machine has a leak. We have changed the hot and cold water hoses and that did not fix the problem. What should we look for next?

Maytag top load washer makes a constant loud noise when washing or rinsing.It does not make the noise when spinning however when spinning it starts and stops jerking back to spin and never goes into the fast final spin that gets all the water out of the clothes. It does not leave water in the tub however.

iI have a LG Tromm washer, it will tumble in both directions but when its time to spin it doesn’t move and makes a racheting noise.
Help ?
Everything is soaked because it won’t spin to drain any water.
could it be the drain pump ?
wouldn’t it need to start draining before the spinning would start ?

We have a Whirlpool Cabrio Model WTW6800WL1 (bought in 2009). Sounds like it is taking off during spin cycles. Seems to be working but so loud can’t hear phone, TV or wash at night when we are in bed it is so loud. Repair man said he was an expert and our home maintenance insurance won’t fix a “noise” issue, even though the repair man said it was something to do with bearings.

What is the possible cause if the washer will not spin in the spin mode? There is a racheting sound but it won’t spin.

Our Whirlpool model WFW9150WW00 washer cannot complete the cycle. The washer cannot – at least to me – achieve a balanced load so it can spin the clothes prior to ending the cycle. ANy suggestions?

I have a model GHW9300PW Whirlpool Duet front-loader washing machine. It had an F02 (drain problem) error code & I had to remove the front panel to get the door unlocked to remove the laundry because it wouldn’t reset to finish the draining process.
Best I can tell at this point, the drain is not clogged. I plugged the washer in again today and was able to get the drain/spin cycle to start (it added water & locked the door), but after that I could only hear a buzzing sound. The drum won’t move & it won’t drain.
Any suggestions on what the problem might be?

I have a duet front loading washer. it 7 years old. the control lock light is lit up. I can’t get the machine to start.

I have a Kenmore front loading washer, about 8 yrs old, that has had what sounds like occasional bearing noise lately during the spin cycle. Today during the final high speed spin there was a bang and the drum slowed right down. I think it broke something… could this be related to the bearings? When I turned the machine off the drum didn’t seem to have a problem rotating back & forth very slowly for a while like it usually does at the end of a spin. If it is the drum bearings is it an expensive repair? — if it is I’m wondering if I’d be better off getting a new washer.

When push the start button it will start but soon it stopped and giving an error code LE

We are working on a 2 year old ge top load washer that will not pin out at the end of cycles.

We have tried a used pump and board, new lid switch and pressure hose.

All hoses, pressure dome and tub are all clean.

This is the second washer of this style were we have run into this problem without being able to figure it out.

It pumps out the water for aproximately 10 minutes before coding out or spinning.

Error codes 16 and 18 (slow drain) keep on happening.

The Frigidaire front loading washer will not spin. it let in just a bit of water and then nothing happens. ive unplugged it and checked that the water supply hoses are not clogged. what do i do next?

Kenmore 90 series
When the machine had completed two loads, a faint smell of “burning” came from the washer. There was no smoke under, on the sides, or behind the machine. Five
minutes into the next load, there was a stronger smell. I checked around the control panel and lifted the top door. There was no hot area or a overwhelming smell that identify
the exact location of the problem. When the machine was in 3-4 minutes of the first spin cycle, the washer shut off. I plugged it into the outlet after a day and a half, and it
worked again. Thank you for your help.