- Guest asked 6 years ago
- last active 6 years ago
My LG washer keeps displaying an error code and i don’t know what it means.
- T&G Appliance Repair asked 7 years ago
- last active 7 years ago
SAMSUNG WASHER SERIAL #Y69Q5AEC803568N manufactured august 2012. pump upgrade kit Dc98-01877a – does anyone have (can get) instructions for this kit?
- David Sutton asked 8 years ago
- last active 8 years ago
replacing a thermister in a samsung wf393btpara /a2 Is this a simple repair or do I have to take off a bunch of stuff?
Is it a just take the back off and there it is?
I have a TE error.
- Tim B asked 9 years ago
- last active 8 years ago
We attempted to repair this machine but will not respond whatsoever. It will beep when pressing the control panel buttons but will not start the cycle. We reset the stackable and the same thing occurs. We also tried replacing the lid switch and main board with no change. We also attempted to put it into service mode in order to look up the error codes in which the stackable would still not respond. Do you know of anything else that could cause this issue? The stackable will just beep three times which we thought to believe would be the lid switch.
- Guest asked 6 years ago
- last active 6 years ago
Hello
Why are the Washer suspension rods are bent on this unit? What is the correction.
Thanks Randy
- David Sutton asked 7 years ago
- last active 7 years ago
Hello, my front-load Whirlpool is making a clunking noise when it spins. When I stopped the machine and started to spin the drum by hand afterwards, I could hear an almost scraping-like noise (almost like there’s a coin or something stuck between the rubber band and the actual drum), but when I pull the rubber band back and look in, I can’t see anything there.
I’m concerned that something has fallen below the drum itself. Do you have any suggestions on how I could get to it or how I should proceed? How bad is this for my machine?
Any help you could offer would be greatly appreciated.
Thanks!
- Jonathan asked 10 years ago
- last active 10 years ago
- Guest asked 9 years ago
- last active 9 years ago
I need service manual for this washer. Or specifically if you can provide a video or repair instruction on how to replace washer drive shaft part number WH38X24734 that will be great. Very loud and wobbling and moving all over the place when spinning. Thank you.
- mdhomeservices asked 6 years ago
- last active 6 years ago
What are some of the things I should be looking that could cause a 7e error code
- Guest asked 7 years ago
- last active 7 years ago
We really can use some advice on a Whirlpool Cabrio washer # WTW6600SG2.
Customer complaint: Set on ‘NORMAL’ the unit will fill and run in the wash cycle for about 15 mins. pause, drops to 5 mins on display, drains and spins, end of cycle.
There are NO fault codes showing or saved.The control was replaced about 1.5 years ago. The unit ran fine after the board replacement.
- Don Kopecky asked 9 years ago
- last active 9 years ago
We really can use some advice on a Whirlpool Cabrio washer # WTW6600SG2.
Customer complaint: Set on ‘NORMAL’ the unit will fill and run in the wash cycle for about 15 minutes. pause, drops to 5 minutes on display, drains and spins, end of cycle. There are NO fault codes showing or saved. The control was replaced about a year ago. The unit ran fine after the board replacement. This unit is located in a beach house and gets only a few months of use a year. Any help or advice would be greatly appreciated.
- Hall Refrigeration asked 9 years ago
- last active 9 years ago
Older Asko washer’s and dryer’s had a fuse holder in back. There was 2 separate parts you had to order – fuse holder and insert. Then they came out with a kit that had both parts in same bag.
Anybody know part number and if still available? Thanks.
- Matt, Ace Appliance asked 9 years ago
- last active 9 years ago
I have a friend that is farther than I want to travel. His washer is making noises and sometimes stops mid cycle. I’d like to talk our way on the phone to find the problem.
Will you send me (us) the diagnostic code ? Or better yet, direct me on how to get this very important tool or where to look for it WHEN I need it when trying to troubleshoot ANY appliance that I’m working on?
Thank you
- Guest asked 6 years ago
- last active 6 years ago
WASHER DISPLAYS F3-E2 CODE
- Guest asked 9 years ago
- last active 9 years ago
My kitchenaid washer is leaking and has a broken lid switch.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
My Whirlpool washer is displaying an error code
- Harley Clark asked 7 years ago
- last active 7 years ago
Display will not work, Random error codes displayed
- Curtis Appliance Repair asked 6 years ago
- last active 6 years ago
The code is no or long fill. The water is coming in ok. The machine will fill about half way up window then it will show code 4e then pump out and start to fill again. And just keeps doing that. I am at standstill. Help. Thank you.
- Guest asked 8 years ago
- last active 8 years ago
experiencing frequent Unbalanced Load error codes from her Samsung top load washer, model wa476dshawr/a1. The unit is firm on the floor and level. The error occurs regardless of the load size or type. Does anyone have any suggestions?
- Johnny Victors asked 9 years ago
- last active 9 years ago
I washer a large load today and now my washer will not spin. I seems to drain and fill ok and I can hear the motor when I put it on drain only setting. Can you please tell me ways to diagnos and fix the potential issues.
Thanks
- Koree asked 10 years ago
- last active 10 years ago
I watched your video regarding washer not draining. It shows instructions on how to remove the drum, however the drum I am trying to remove is stuck, Ive tried what your video says and im not sure if I missed anything because no matter what I do, it will not budge. Any suggestions
- sean asked 9 years ago
- last active 9 years ago
I am getting an F35 error on my washer as well as “SUDS” coming up. Been trying to find a video that might help me diagnose and repair it myself. Any thoughts on what could be causing it? Trying to get some direction.
- Harold asked 10 years ago
- last active 10 years ago
Just wondering how to do a continuity check on a GE motor 5kh41jt18as has a yellow orange blue red black wires or if I were to make up power cord where would I hook it to and also where is the capacitor on this motor
- Guest asked 8 years ago
- last active 8 years ago
WHAT IS IT AND HOW TO REPAIR IT?
- ELLIS asked 9 years ago
- last active 9 years ago
this unit on the rise cycle will stop and get a blinking led. I have the teck sheet but cannot make out how to read the error code.the led status are 1,o,* and so if it is blinking on rise which one would i read? This is on the critical fail mode table and then it has the No critical fail mode table. What i did on this unit i replace the tranny ot what they call support. I was not doing this before the repair, I do hear the lid lock trying to lock, like the strike is in the way of the lid switch
- Guest asked 8 years ago
- last active 8 years ago
This is a replacement kit found on many samsung washers there are no videos explaining how to do this. Please add a video thank you
- Guest asked 8 years ago
- last active 8 years ago
Parker &Fisher, not spinning motor getting hot? Is there a way to know transmission is bad? How do you put this machine in diagnostic mode?
- Guest asked 8 years ago
- last active 8 years ago
