At start of cycle door locks then pauses . at times it won’t release. I cannot get the service test to activate. Which is the left button under the display? There instructions are very confusing. I have the tech sheet but a service manual may help. Any videos on this would help especially on the diagnostic mode.
- Guest asked 8 years ago
- last active 8 years ago
A service manual would help and any videos.
- Guest asked 8 years ago
- last active 8 years ago
the fan evaporator motor and the damper to the fresh food is jerking back and forth
- Guest asked 8 years ago
- last active 8 years ago
Makes ice seldom leave and then melts and runs out onto the floor did it in error code for icemaker test drive noted in bed going to replace icemaker but I’m assuming I have a cooling issues also
- dwoods asked 8 years ago
- last active 8 years ago
when this happened i tapped on the right pressure switch and it would fill. i replaced switch and it still happens also when it does fill it only fills halfway. this only happens on rinse, works fine during wash cycle
- Guest asked 8 years ago
- last active 8 years ago
are you sure your video for ice maker removal is complete?
- Guest asked 8 years ago
- last active 8 years ago
are you sure your video for ice maker removal is complete?
- Guest asked 8 years ago
- last active 8 years ago
I asked how to get the door apart. What I got was a video on how to change the door latch it’s attached to the tub no help.
- Guest asked 8 years ago
- last active 8 years ago
Closing of French doors or freezer drawer hear a high pitch noise. Doesn’t run long enough to hear where it coming from.
- Guest asked 8 years ago
- last active 8 years ago
This is nuts. How does the door come apart on this thing. I cannot find one screw on this door. Also is the water valve on this thing 110 volt being all I get to it is 10.3 volts. Dishwasher won’t fill. I think the diagram is inside the door since it’s not under it. Thanks for your help.
- Guest asked 8 years ago
- last active 8 years ago
Makes ice seldom leave and then melts and runs out onto the floor did it in error code for icemaker test drive noted in bed going to replace icemaker but I’m assuming I have a cooling issues also
- dwoods asked 8 years ago
- last active 8 years ago
The door on my range will not close properly.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
The control panel on my GE range is not working.
- James Buchanan asked 8 years ago
- last active 8 years ago
I am having trouble getting the burners to light on my range.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
i believe the door seal is damaged on my GE oven.
- Harley Clark asked 8 years ago
- last active 8 years ago
This is a commercial whirlpool washer it says. I cannot get it in diagnostic mode.It says to unplug , start at 12 o clock, turn dial lt, rt, rt lt rt. the sense light blinks when I plug it in. then if you hit start it stops blinking. after about a minute or so the red lock light starts blinking. it will not throw a code. the sense light just stays on.
- Guest asked 8 years ago
- last active 8 years ago
This code says cooling fan speed too low or won’t come on. Do you have a video on this one and a service manual and any tips?
- Guest asked 8 years ago
- last active 8 years ago
The door on my range will not close properly.
- Gary Williams asked 8 years ago
- last active 8 years ago
The door will not stay shut on my oven.
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
My oven is not keeping the proper temperature.
- Gary Williams asked 8 years ago
- last active 8 years ago
I think the spray arm on my dishwasher is broken.
- Curtis Appliance Repair asked 8 years ago
- last active 8 years ago
