Repair Help

We are servicing a Bosch dishwasher that completes the cycle but doesn’t dry the dishes, water remains in the diswasher after cycle. Any suggestions on where to start?

We are servicing an ASKO washer that fills and drains but doesnt agitate. The washer doesn’t have a model number only a serial number. Any ideas on where to start with this washer?

hi. this unit is making noise when door is closed. there is ice building up on the evaporator.i seen the pictures on how to install the above insulation kit.but still confused,do the strips of insulation go underneath the drain pan and on the backside of the metal plate behind the evap coils. so that when the coils are back in place the strips cannot be seen.thanks

Hello, We have a freezer that doesn’t keep the temperature and everything thaws. We empty the freezer and then it starts working again.
We would like to know what is wrong, what parts we need to get, and need help in fixing it.
this has happened before, and it worked for a year and it happened again. It is definitely something that needs to be fixed and we want to repair it before we use it again.

The problem is that someone changed the front left burner (3 stage) and they put the wires in the wrong order. I have a new burner and I would like to know which color wire attaches to which pin on the burner, the colors are Orange, Blue and Grey., and there are 3 pins on the burner. I am concerned with attempting to go on a peck and find method in case it damages the new burner.

Is there a defect in this model? It catches and tares clothes. They get caught in gap between the basket and the bellow. The bellow is in good shape. The wedge in the 11:00 position is OK.

Unit dead, no display.
Found vent thermostat (diagram part 115) scorched with riveted terminals sloppy loose. Connecting wire and stake on terminal cooked.
Jumpered terminals and microwave worked fine.
Ordered part three times but it keeps arriving N.O. Instead of N.C.
What could I be missing or where can I get the proper N.C. Thermostat (150degrees) I believe?

No power to refrigerator, sorry This is the right model number. LFC20760SB for the LG.

Whirlpool dishwasher WDF520PADM3 will fill but will not run. It will drain however.

I am working on a Maytag dryer and the problem is a grinding noise when turning, I replaced the drum guide wheels but the noise persists. Also when I run the drier now the tensioner keeps sliding out of the bearing holes so I am wondering if anyone knows why the grinding noise persists and if the tensioner should have some kind of retaining clip is prevent it from slipping when drum rotates.

I posted a question about a week ago and I checked the refrigerator drain and pan and they are clear and the water tank also. The water is coming from the refrigerator room at the bottom on the left side where there is a vent and damper control. Where does the air supply come from for that vent? I am not talking about the vent in the back. near the water tank where the fixer box and fan is in the rear. The water under the drawer comes from that front vent. The customer says it is often iced up.

Ice maker won’t work? When you use test button nothing happen no fill or rotation of the ice maker.

Dishwasher motor won’t run. When you it cancel and close the door the dishwasher drain all the water. Push top control for normal wash and it start close the door and you can hear it fill with water. The dishwasher won’t power up the sprayer motor.

the compressor is running.
it was very very hot to the touch.
but it is running and not cooling

the compressor will kick on and then go out rite away .
then a few minutes later it will do the same

when I disconnected the water filter I was able to get a bit of water out thru the dispenser on the door.
when I put it back the flow was very very low to nothing.
and the ice maker is not making any ice.

The machine is making noise during the spin cycle. Now it’s completely shutting off in the middle of the spin cycle. What should I fix? It is showing an error code of 3E.

We have a dishwasher that, what ever the remaining time, adds additional time. If there is 40 minutes left it’ll then add more time and show it has 90 minutes left. This happens with every cycle. Main control board has been replaced and the same issue continues. Any suggestions?