Repair Help

I need a new door seal for this model, anyone have time to do the lookup for me? Thanks.

Went out and found the pump clogged, tied up with rug fibers and pieces. Cleared it and the drain to ensure proper flow, still getting a very slow drain, and sometimes doesn’t drain at all. Pump ohm’d out, not sure what I’m forgetting.

Not very knowledgeable on these yet and am wondering if it’s a bearing like many other brands? Has a slight rubbing noise as well, am thinking it may be more than one thing but not sure. Any help would be great.

This unit is in an unheated garage, seems to run constantly. Have checked major components and they seem fine, I must be missing something?

Just wanted to post a reminder to all those out there that may read this: I’ve had more burning smell & lint build ups this year than ever before. Just came across another today. Many have had a flame rollout has already caused some burning lint and there’s limited air flow causing long dry times. Please be sure to clean out these dryers if you’re in there working on them already, and if you can’t get the vent completely cleared, have a professional come do it, or strongly suggest it to the customer. This becomes such a serious fire hazard when left alone and unnoticed.

Looks like the relay on the control board for their gas heat is bad & it needs a control module. Problem is, we don’t do many of this brand and I don’t have a lookup for this dryer. Any way someone could get me part information?

Had the customer defrost the unit to get the cover off, looks like a conductor in the drain might solve my problem. Do you guys do this often? Is there a part replacement I’m missing? Hoping I didn’t overlook anything, but seems like the backed up and frozen drain was the main issue.

This unit just runs non-stop, does not shut off. Ohm’d everything out and looks like the pcb board is bad. In need of a part number and cost if you have it.

I had an element replacement come up as a whirlpool 35001247. Is that right? I was thinking it’d be a DC number or a different prefix. Wanted to make sure this wasn’t an error before ordering. Thanks.

What causes this? I’m a new tech here and there is no spec or information sheet. Thanks.

No tech sheet I can find, what am I looking at in terms of parts to correct this? Runs for a few minutes, then quits and errors out.

Also looking at this dryer and need the duct heater if you have a minute to get the information for me?

This unit isn’t starting, I think I’ve narrowed it down to the idler pulley but can’t find a schematic for the lookup and part information. Any help?

was told everything is running but not getting cold on fridge or freezer

Looking at it now and there’s no tech sheet. Thanks.

Have a whirlpool refrigerator model GI6FARXXY07
the evap motor is not running.

Dishwasher was flashing on smart auto normal. I tried to clear by turning power off for approximately 5 minutes still had same problem. I replaced main control board unit ran Ok while I was there testing it . Customer called back and said unit is doing the same thing.

This dryer is in an apartment laundry. The complaint from residents is the dryer turns itself off and shows there is still time remaining but the dryer is not running. I suspect this would be a timer issue. When the dryer is running the temperature at the vent is approximately 155 degrees. A couple of other questions I have about the coin operated aspect is, Can you set the time for how long the dryer will run on a set of quarters or is the only setting you can adjust is how many quarters it takes to run a load. There is a similar complaint on a second whirlpool dryer at this same location. It does not stop mid cycle but it does not dry the clothes with one set of quarters.

I set my washer to run, it fills with water, starts to wash and the timer advances to completion in about 3 minutes. It does not do the spin cycle but he states it does drain. Any ideas what this might be? Thank you in advance.

Model – 253.26082100 Serial – WB63832311

Display in door flashing CE. Disconnected / reconnected wiring harness from control board that goes to display. Did not changed anything . Found upon opening door slowly display would clear out CE and then come back as you moved door.
Suspect wiring harness in door problem. Parts breakdown shows harness in bottom of door, but no part number. Anybody come across this before? Are you able to replace this harness? Thanks in advance

GE wsm2700dawww makes loud clunking sounds when turning any recommendations ?

f3 e2 error when you use the micro I replaced the erc because there was no display now I get this code and I already checked sensor I was thinking about installing another erc

if I check water inlet valve for bosh dishwasher and it has continutity to water valve does that mean valve is ok

DOOR WONT LOCK AND MACHINE WONT DO ANYTHING, what is the most probable; door latch, control board or ?…
Thanks for your help

I have installed three sets of door hinges. I know these hinges don;’t work because I have run into a few of these stoves.
Has anyone heard of a solution to this? Whirlpool has to know about it because I had my parts supplier inquire a year ago. I had one customer that was ok with a latch on the side of his stove. Any suggestions ?
Thanks,

I have this IN WALL OVEN with an F7 E6 ERROR
From what I read it says control panel problem, I think it’s a membrane that has gone bad
But I can’t find a part number for that… anybody have a clue?

We have a Maytag refrigerator . We had replaced the icemaker and the water inlet valve on this unit 4 months ago.. We have a low water level at fill and the partial cubes are hanging up on top. The unit has good water pressure going to it and a new water filter. Has anybody run into a problem other than the water inlet valve being the cause of this problem? I’m having a hard time with a water inlet valve on city water failing in 4 months.
Thanks in advance

I got it apart and found a level sensor that I think is bad, but doing the lookup I am having a hard time finding the correct part number. It’s the water sensor if that helps. Not with the unit to give you the model #.

The unit has a lot of condensation and thawing happening, but everything checks out. Looks like door may have been jammed open by it’s contents, or not closing correctly, but would this be the root of the problem?