Have 14 vdc at user interface
- Guest asked 5 years ago
- last active 5 years ago
I replaced the touchpad panel about 2 weeks ago and now it is acting up. It finished a cycle and the clean light came on but two other LEDs came on faintly and are now constantly on…….nothing can make them go out .
The LEDs are for the “Potscrub” and “Heat Dry” if that helps any.
I hope the panel isn’t toast already and if so WHY??
- Clay asked 11 years ago
- last active 11 years ago
I am getting a 6C3 error code on my dishwasher. Also it will not do anything.
- Patrick's Appliance Service asked 5 years ago
- last active 5 years ago
Our dishwasher quit working and is flashing an ER code. How do we diagnose what it needs?
- Chris Higginbotham asked 11 years ago
- last active 11 years ago
My dishwasher will not start. The lights light up when I choose different functions but it won’t actually start when I press Start. I tried the reset by pushing the High Temp Scrub and Energy Save Dry buttons alternating five times each and the unit will go through the reset. It also drains when I press cancel after resetting. I am not sure how to proceed.
- Ryen Mullen asked 11 years ago
- last active 11 years ago
Customer complains that his dishwasher Silverware rack dosnt dry at all, but the rest is dry???
- Guest asked 8 years ago
- last active 8 years ago
Not heating, blinking complete cycle not staying solid
- Guest asked 10 years ago
- last active 10 years ago
Asko Dishwasher fills, clicks 3 times, flashes “delicate wash” after new inlet valve installed, old valve was leaking bad, new valve seems good fills to the proper level as far as i can tell but cycle doesnt continue. Tested resurculation motor that tested good and had continuity and their initial complaint was leaking which it no longer is leaking. drains fine, water switch and door switch seemed to be fine..?
- Guest asked 6 years ago
- last active 6 years ago
Not sure what’s happened to our dishwasher door, it seems to not really ease open like it used to.
- Esther asked 11 years ago
- last active 11 years ago
Hi Folks,
This unit is showing the following code: Under the cycle mode there are 3 lights blinking, the first two and the fourth i.e. Smart Auto – Normal – Skip –Delicate! Also, while the door is open the pump is on and pumping out. According to the troubling shooting guide this all relates to high temperature water entering the unit. Although it says nothing about the unit working with the door open. Can someone please point me in the correct direction?
- Guest asked 10 years ago
- last active 10 years ago
My dishwasher is not mounted in the wall properly.
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
I am looking for a tech sheet for this dishwasher. Initial diagnostic mode we determined the door latch and strike should be replaced. The homeowner previously replaced the wire harness and main PCB board. After replacing latch the machine won’t start. When go into diagnostic all lights blink even when door is shut. Will not enter service mode at all. Hopefully you can send a tech sheet for this model please
- Guest asked 7 years ago
- last active 7 years ago
Its fills with water and drain it right away
- Guest asked 10 years ago
- last active 10 years ago
The door on my dishwasher just slams shut.
- Curtis Appliance Repair asked 8 years ago
- last active 8 years ago
A service manual would help and any videos.
- Guest asked 8 years ago
- last active 8 years ago
I was advised to switch the button control units as the top drawer selector will not move from rinse.
How do I access those controls? Is there a walk through? Diagram?
Do I need a serviceman yet??
- Ed asked 11 years ago
- last active 11 years ago
I purchased this Whirlpool dishwasher in Dec. 2014 from Home Depot. It has run flawlessly since then, up to 3 days ago. Now when the Start button is pressed all the lights come on and I hear the water filling in, but the upper and lower fans that distribute the water do not move. When I open the door I find the water settling in the bottom. When I press cancel, the pump is activated and the water in the bottom of the dishwasher is pumped out. I disconnected power to the dishwasher hoping to reset the control panel, but disconnecting the power did not change the situation. So the dishwasher now just sits there with all of the lights turned on with no activities. The lights that are on are for Normal Cycle, when I press that button again, the Normal Cycle light jumps to 1-Hr Wash and goes back to normal immediately. Cant get the Heavy Cycle or the Soak and Clean Cycle lights to light up. The other lights that are on are Heat Dry, High Temp, Sani Rinse. I cant change those lights by pressing the Options. By the way i removed the filter and cleaned it, but it was not clogged with debris
Could the control panel be the cause of this problem, or the motor that activates the water distribution fans. What part could be the major reason for this defect.
- Guest asked 8 years ago
- last active 8 years ago
The normal light flashing, and only the normal and cancel fonction ,i Check the element ok, the drain pump ok, door lock switch is ok , fuse ok . What is the problem.
- Guest asked 8 years ago
- last active 8 years ago
Kenmore Elite dishwasher made by Whirlpool that will not drain properly every time. Will work 1 or 2 cycles then at the end of the 3rd cycle will leave about an inch of water in bottom of the dishwasher. Everytime I drain the dishwasher through the cancel cycle it does just fine.
- Guest asked 10 years ago
- last active 10 years ago
Fills but does not drain goes through cycle except for drain
- Guest asked 7 years ago
- last active 7 years ago
Customer gave no details of when the dishwasher gives the code, only that it reads the code: nE.
- dwoods asked 5 years ago
- last active 5 years ago
Unit will run to countdown of 1 on timer then stays there running without draining. Yet it will drain fine if reset or stopped and another cycle is started. Its spotlessly clean and customer just stops it, resets it so it drains and takes her dishes out. Aqua sensor? board? Cant find a diagnostic manual for this or a tech sheet. Im just learning dishwashers.
- Guest asked 8 years ago
- last active 8 years ago
The customer showed me a video that sounded like the pump running with the door open. She said that it shows an error code often of 10 and last time it showed 30.
Where is the tech sheet hidden? I couldn’t find it behind the door panel or behind the toe plate.
I need a copy of it and the error codes and videos.
- Guest asked 5 years ago
- last active 5 years ago
I’ve replaced the main board and heater already myself but must have done something wrong because the HE error code is still coming up. Did I get a bad heater? Or could there still be a different issue? Thanks for your help.
- Fred Abernethy asked 10 years ago
- last active 10 years ago
I watched this video and was able to disassemble the dishwasher, clean the parts, and reassemble most of it. https://www.youtube.com/watch?v=VtRWr78dbJc
However, when I try to reattach the bottom spray arm, the part that should screw in tightly to secure to bottom arm will not fit in securely. So the bottom spray arm just sits on the tube and wiggles. I can get the part to secure tightly to spray arm by tightening it counter clockwise but not to the tube.
Thank you.
- Guest asked 7 years ago
- last active 7 years ago
Hi –
My kitchenaid dishwasher (3 years old) is leaking water under the right bottom side of the door. It is not a lot of water, and my first attempt to fix it was cleaning the seal, which had some small amount of scum on it. This fixed it temporarily, but a few days later the water leak was back. It is not a lot of water, and doesn’t happen during the rinse only cycle, apparently. Any ideas/thoughts on this would be very useful. It is a stainless steel kitchenaid dishwasher, similar to model KDTE104DSS.
Thanks!
Adam
- Adam asked 11 years ago
- last active 10 years ago
- Phyllis asked 11 years ago
- last active 11 years ago
Gentlemen, I have not checked this unit yet the complaint is a no drain issue. Do you have any service information available that you could share with me on this Dishwasher. It would be a great help and greatly appreciated. Any service bulletin or service advise is always appreciated as well. Thank you for your help.
- Guest asked 8 years ago
- last active 8 years ago