0 votes
19k views

How can I winterize my dishwasher for my summer cottage. I drain all the water from the system and use the air compressor to finalize so no water is in the lines. RV antifreeze to the traps.
Can you assist? I saw many of your you tube videos for how tos but not on the dishwasher winterization
Thanks

  • kathy mccarthy asked 7 years ago
  • last active 7 years ago
0 votes
18k views

I repaired the drain pump on my dishwasher. Now I can’t get it to start.

  • Paul Bergstrom asked 7 years ago
  • last active 7 years ago
0 votes
18k views

Samsung dw 1E error code, model DW80F800UWS/AA, serial B009g9md604628d
This is supposed to be a high temp heating error. Had schematic for DMT800 series dishwasher with me. This wire diagram did not match the wire diagram on the main pcb cover on dw. Did not see thermistor listed on dw wire diagram on unit.
Heating element had 12 ohms, but no power going to it in quick wash cycle. Could not get it into diagnostic mode.
What should I be checking? I am guessing you need to pull the unit to get to components like LG brands?

  • Ted Hood asked 7 years ago
  • last active 5 years ago
0 votes
13k views

Hi –

My kitchenaid dishwasher (3 years old) is leaking water under the right bottom side of the door. It is not a lot of water, and my first attempt to fix it was cleaning the seal, which had some small amount of scum on it. This fixed it temporarily, but a few days later the water leak was back. It is not a lot of water, and doesn’t happen during the rinse only cycle, apparently. Any ideas/thoughts on this would be very useful. It is a stainless steel kitchenaid dishwasher, similar to model KDTE104DSS.

Thanks!

Adam

  • Adam asked 7 years ago
  • last active 6 years ago
0 votes
13k views

hi , i am an appliance repair man in canada, and i have a customer that has an 3C error mid cycle, i went there ran the machine for 10 minute nothing came up, tried to manually drain the machine drains fine, cleaned the filter, but dont know where to look for this error, nothing seem to be wrong with the machine.. please help

0 votes
12k views

I own an appliance repair company in Texas. I have found the upper rack may disengage from the rails when the
customer pulls the upper rack out to load or unload the dishes
Wheel axle breaks and causes upper rack to fall when pulled out on many of the dishwashers.
Any suggestions would be greatly appreciated thanks in advance James.

  • James Londen asked 7 years ago
  • last active 6 years ago
0 votes
11k views

What does this part do? Does it recycle the water. I would like to know. Will it stop the dishwasher from turning the motor on if it doesn’t work?

  • Guest asked 5 years ago
  • last active 5 years ago
1 vote
11k views

Hi,

I need to replace my waterwall vane motor and have ordered the motor (part number DD31-00013B). I watched the video on how to remove the motion assembly and waterwall but I’m not sure how to remove the old motor and install the new one. Does the old motor drive pin just slide out and then just slide the new motor in or is there a seal i need to replace?

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
10k views

The unit keeps getting a low water error and everything I could think of checks out: inlet valves, water pressure, fills with correct amount of water, board/panel is fine, cleared some minor debris from the pump, and checked that the float works. What am I missing?

0 votes
10k views

Dishwasher fills and runs for a while, then stops mid cycle with an E17 error.

0 votes
9k views

My Samsung dishwasher is displaying a 4c error code.

0 votes
7k views

Pump motor constantly running giving error code i30 checked drain pump everything working fine

0 votes
7k views

Customer called with a Samsung dw model DMT400RHS, lights flashing on SMART AUTO and HEAVY.
Does anyone know what this code means?

0 votes
7k views

The Smart Auto and Normal LED’s are flashing per the customer. I found the motor/pump locked up due to lack of use, unstuck impeller, unit running. Not sure what the flashing LED’s reference.

  • Guest asked 7 years ago
  • last active 6 years ago
0 votes
6k views

I have a GE dishwasher and the Vent Cover keeps “Popping Off” and the is Vent Leaking . Is there a fix for this issue ?

0 votes
6k views

My Bosch dishwasher is not working properly.

0 votes
6k views

Water leaking to pressure switch area through black hoses.
I dried the area and AE back again.
When I opened door I saw water being directed to front of door on ledge from water input.

  • Guest asked 5 years ago
  • last active 5 years ago
0 votes
6k views

Above Samsung dishwasher flashes lights for “Smart Auto” and “Normal”. User manual says it is a “heating over temp” error. Could not find tech sheet on unit (I don’t think they put one on the unit.). I Kept a service mini manual from a previous. Looks like the temp thermistor is bad, not the PCB. Has anyone else run into this type of problem with this brand?

0 votes
6k views
0 votes
5k views

I’m getting 7E error and grinding noises at certain points. It used to wash for a while, then stop with the 7E error. I checked that the water wall part that moves was attached properly and oriented correctly. Ultimately, I replaced the motor/sensor assembly. Now, when I start it, the water wall cycles back and forth, making a grinding sound when it gets all the way to the back (I think) and then displays 7E before even starting to fill. I can’t find anything binding. I removed the water wall track and it moved smoothly. I saw people on the internet saying that there is a problem with a magnet getting weak from the heat and no longer activating the sensor at the end of its travel. Could this be my issue? How to resolve?

0 votes
5k views

Our dishwasher quit working and is flashing an ER code. How do we diagnose what it needs?

  • Chris Higginbotham asked 7 years ago
  • last active 7 years ago
0 votes
4k views

Issue with Samsung Dishwasher.

0 votes
4k views

Not drying properly.

1 vote
4k views

HOW DO I TROUBLESHOOT THIS? I SUSPECT BAD WATER VALVE. NO WATER IN TUB AND COMING UP WITH U6 ERROR CODE. THANKS.

0 votes
4k views

My Blomberg dishwasher (model: DWT 34240 NBL00) is showing error code “IF” then “88” and then “IF”. All the 4 wash cycle lights glow continuously and no button works except “ON/OFF” push button.

  • Gary asked 7 years ago
  • last active 7 years ago
0 votes
4k views

My Dishwasher is displaying a AE6 error code.

0 votes
4k views

Question is about this repair: https://www.appliancevideo.com/premium/samsung-dw80j9945us-dishwasher-leaking-from-the-sides-of-the-door-water-wall/

I’m actually having an issue with the 7e error code trying to find information in regards to that replaced the sprayer arm assembly as well as the motor that runs it still giving the same code trying to see if there is a test for it or if I have to run the machine through test mode so that it understands it has a new motor new motor is running the old one would not but it is making a thumping noise like as if it is trying to run one direction to far or the other direction to far

 

 

  • laron01 asked 4 years ago
  • last active 4 years ago
0 votes
3k views

Will not drain water.

0 votes
3k views

The dishwasher start/cancel button will press bit does not rest or start. I flipped the breaker for 10 minutes and it continued to do the same thing. I set it on 1 hr delay thinking maybe it would start. It locked up and no cycle buttons, delay options, or extras like heated dry will change now. I flipped the breaker and left it off the rest of the day. Last night (about 5 hrs later) it’s still flashing at me. I used it Saturday with no problems. Sunday it started with this mess. My 4 yr old did spill water on the counter and into the floor but the dishwasher is completely under the lip of the countertop. I doubt that enough water may have gotten on it but if it did then why did the other buttons work before flipping the breaker. The dishwasher is about 2.5-3 yrs. I use it 3-4 times per week. We’ve checked the filters and the ensured that the racks were in properly.

0 votes
3k views

THANKS FOR YOUR HELP on our Frigidaire dishwasher. WE ALREADY FORKED OUT $120 AND REPLACE THE CONTROL BOARD AND THE ERROR CODE IS STILL FLASHING. I GUESS WE NEED TO WORK ON THE TOUCH PANEL OR CONSOLE, HUH? That should do it, right? Is there a video showing how to do this?

CHRIS HIGGINBOTHAM

  • CHRIS HIGGINBOTHAM asked 7 years ago
  • last active 7 years ago
Showing 1 - 30 of 812 results