Repair Help

Hi,
I am getting an error code of F3 S9? Can’t seem to find this code anywhere? Anyone have any ideas?
Thank you,
JAN
Barney’s Appliance
Palm Bay, FL

I’m trying to do a repair on a washer that’s not even 2 years old yet. The Le code won’t go away. I replaced the motor sensor the diverter motor the stator looks fine so does the rotor and bearings but still get a grinding noise. When I put it on a spin and rinse cycle it will work for 3 minutes but grind and the Le error code will show up again. Very frustrating so little help would be nice lol.

Thank you

Hi am trying to check a beverage cooler to see if it has a leak and I want to make sure I get the proper reqding even if .it is an aproximate reading to have somewher to start please advise.
I forgot to look for the brand but it is a monster cooler and I assume it is the same as the coca cola beverage coolers
i will go back and look at the brand if you need it to help trouble shoot.
Thanks

Hello, I have a dryer that you can’t move off the cotton setting other then that it works fine. I change the face board with 2 different faces and I got the same thing any thoughts?

WOULD LIKE ANY SERVICE INFORMATION ON THIS L.G. DRYER. HOW TO PUT IT IN THE DIAGNOSTIC MODE.
SCHEMATIC/ WIRING DIAGRAM. I HAVE A LOW OR NO HEAT ISSUE. THANK YOU FOR YOUR HELP. HAVE NOT CHECKED ANYTHING ON THIS UNIT AT THIS TIME. SERVICE INFORMATION WOULD BE A GREAT HELP BEFORE I DO ANY CHECKS. Thank you again for your help.

I NEED TO REPLACE THE MOTOR AND TRANSMISSION ON THIS WASHER. I HAVE TO DO IT ON SITE I CAN’T FIGURE OUT HOW TO TAKE THE TUB ASSEMBLY OUT TO REPLACE THE MOTOR AND TRANSMISSION PLEASE ANY HELP IN THIS WILL BE APPRECIATED.
THANK YOU

I replaced the control board and nothing changed , I need help ,it is too expensive to guess anymoore

the pump keeps running and im getting i30 tried resetting but i did not help

ICE MAKER IS TOO WARM TO MAKE ICE. I HAVE REPLACED THE ICE MAKER, WATER VALVE AND AUGER MOTOR BUT STILL IT IS STAYING WARM
THANK YOU

I have a washer that sounds like a jet during the spin cycle.

hi i saw the breakdown here but it doesn’t show screws or video. is this pretty straight forward?

i am curently working on a side by side refridgerator and the freezer is working fine but the refridgerator side is warm
I checked the air inlet at the top left and it is open completely and still not cooling.

Exhaust temperature too high.
Felt Seals look good.
Smelled burning smell.
Does the thermostat 6931EL3002A on the blower housing regulate temperature i.e. turn burner heater on and off. Alternatively the thermostats on the tube turning the burner on and off.

I need both door gaskets,complete icemaker

i need a service manual on this or what ever you have available. tx the customer says that it’s stops cooling and after it is unplugged and plugged back in it works again repeating the cycle. any thoughts?

I NEED TO REPLACE THE COMPRESSOR FOR THIS UNIT. I DON’T KNOW HOW TO GET THE THREE WAY VALVE INTO THE HOME POSITION. IF YOU CAN FIND THE SERVICE MANUAL THAT WOULD BE GOOD. IF YOU DON’T HAVE THAT, SEND ME WHAT YOU CAN FIND PLEASE. TX

I would like a video or something on replacing the French door seals.

the oven will heat up and then go off after some time and the bake light will blink. I changed the control board and it didn’t helpll

Customer states that they have to chip or melt the ice out of the ice bin periodically. The ice door does not seem to be having any problems closing and seems to be tight. Any thoughts on why the ice is freezing together. I am thinking maybe water valve or the filter, although homeowner says they just changed the filter. Any assistance is appreciated.

the customer complaint is the machine make a grinding noise and doesn’t produce much ice

I sent a question earlier and forgot to put the information that I need to share, I cleaned the dishwasher that was very dirty and so I cleaned it and it ran good for 3 washes and the customer called and said it stopped working,
thanks

I went to the customers house and there was water in the bottom so I shop vac it out and still nothing please advise me on what to check and how to trouble shoot the problem.
Thanks