0 votes
3k views

Keeps displaying an error code and i do not know what it means.

0 votes
2k views

Problem with a LG Washer

0 votes
4k views

Dishwasher is having some problems

0 votes
2k views

Having an issue with a Refrigerator

0 votes
2k views

The light on my GE dryer is not working.

0 votes
2k views

Refrigerator is having some problems

0 votes
2k views

My LG washer will not respond.

0 votes
2k views

Having an issue with a Refrigerator

0 votes
3k views

The controls on my dryer will not respond.

0 votes
3k views

Having an issue with a Washer

0 votes
2k views

Having an issue with an Ice Maker

0 votes
3k views

not drying properly.

0 votes
3k views

I need technical advice. This is the second time in the last 6 months this has happen. What is causing the failure to reoccur ?

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

I just replace the water valve in this refrigerator.
The initial complaint was the customer change the water filter. Bled out about 2 gallons, and then it stopped working.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

I checked the cut off thermostat and we’re good. I also replace the relay control board on the back of the unit. I also noticed that the convection fan wouldn’t turn on. There’s power to the display board and it responds pretty good.

  • Guest asked 9 years ago
  • last active 9 years ago
1 vote
4k views

I just need to know how to detach the Blue water hose from the back top right side of the refrigerator.
I pulled the grey one easy but the purple one I can’t pull it it is stock, my question is if the hose you detach it from the back or from the inside of the refrigerator where the ice maker compartment Is.
Please provide me with the installation immediately, thank you.

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

WHEN THE MACHINE GOES INTO AGITATE IT MAKES A LOUD RUBBING SOUND.
IVE LOOKED UNDER THE MACHINE AND I FOUND THE BELT RUBBING AGAINST THE PLASTIC HOUSING COVER OVER THE THE 2 PULLEY WHEEL.
IVE PUT THE BELT BACK ON PROPERLY AND IT STOPPED FOR 2 TIMES
AND THEN ITS STARTS AGAIN.
THE BELT SEEMS TO BE SLIPPING TOWARDS THE END OF THE WHEEL AND RUBBING AGAINST THE PLASTIC

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
3k views

Svc Manual says to check HIGH/LOW signals from HALL SENSOR in MICOM PIN
If EJECTOR is in place: It is an initialized control so the mode can be changed to ice making control Then it goes into some discussion of if the EJECTOR is in place within 2 minutes or if it is in place within 18 mins. Im used to sticking my short piece of Romex into the different slots to check different functions, I have never seen an ice maker with electronics on the head piece. Can you experts help me. Ice maker worked till I removed it and then re=installed it. Tried new ice maker and a new inlet valve with same no ice results. Thanks

  • Guest asked 9 years ago
  • last active 9 years ago
0 votes
2k views

My Whirlpool refrigerator is not producing ice.

0 votes
3k views

Can you tell me what could be causing this issue on a Bosch Dishwasher? It is having these problems: Will not run

0 votes
2k views

My GE refrigerator is not making ice.

0 votes
3k views

Hello I have a question on a Jenn-Air Oven. I’m noticing these issues: Oven roller rack could fall off

0 votes
3k views

Having an issue with an Ice Maker

0 votes
2k views

My Samsung dishwasher is not drying the dishes properly.

0 votes
2k views

The water will not drain out of my dishwasher.

0 votes
3k views

Refrigerator is not working right

0 votes
3k views

Will not tumble.

0 votes
5k views

My Whirlpool washer is displaying an error code

0 votes
2k views

Washer is not working right

0 votes
2k views

Jenn-Air Oven that is not working

Showing 5401 - 5430 of 9k results