My control panel does not seem to be secure on my Whirlpool washer.
- Harley Clark asked 10 years ago
- last active 10 years ago
My Fisher & Paykel washer is ripping clothes during the wash cycle.
- Harley Clark asked 10 years ago
- last active 10 years ago
My Samsung dryer will not start and is completely unresponsive.Any suggestions?
- Harley Clark asked 10 years ago
- last active 10 years ago
My Whirlpool refrigerator is not cooling properly.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
My Refrigerator will not make ice. Any suggestions to help with this problem?
- Don Kopecky asked 10 years ago
- last active 10 years ago
Can you tell me what could be causing this issue on a GE Refrigerator? It is having these problems: Not making cubed ice
- Don Kopecky asked 10 years ago
- last active 10 years ago
The dispenser door on my Kitchenaid dishewasher will not close.
- Don Kopecky asked 10 years ago
- last active 10 years ago
My Whirlpool refrigerator will not dispense ice. Any suggestions?
- Harley Clark asked 10 years ago
- last active 10 years ago
The ice maker is not working in my GE refrigerator.
- Harley Clark asked 10 years ago
- last active 10 years ago
The dishes are still coming out dirty after a cycle. Any suggestions to resolve this issue?
- Don Kopecky asked 10 years ago
- last active 10 years ago
The food in my Kitchenaid oven does not cook properly. Any suggestions?
- Harley Clark asked 10 years ago
- last active 10 years ago
My Electrolux washer is not cleaning clothes properly.
- Patrick's Appliance Service asked 10 years ago
- last active 10 years ago
my GE washer has a crack in the glass. How do i fix this issue?
- Harley Clark asked 10 years ago
- last active 10 years ago
My Samsung dryer is not drying clothes properly.
- Don Kopecky asked 10 years ago
- last active 10 years ago
so I have changed the electronic control board.
and I am still having the E51 error
- Guest asked 10 years ago
- last active 10 years ago
only the heat or steam light is on.
nothing else seems to work
- Guest asked 10 years ago
- last active 10 years ago
Need to change the bearing and seal and if there is any special tools to remove the bearing? Video for the repair would be helpful.
- Guest asked 10 years ago
- last active 10 years ago
Error code F6 E0 what does it mean and can I have a tech sheet for this unit thanks.
- Guest asked 10 years ago
- last active 10 years ago
Model Number
rf236teaeww/aa
What have you tried so far?
I have checked the ice door and it is OK. Replaced the ice room seal and it still leaks .
That ice room gasket didn’t solve the issue. Do you have any other ideas? It seems that the ice is very soft and the crusher makes it almost like snow and it dispenses much of it but just enough remains like snow on a tree limb and then melts and seeps through the hatch.
- Guest asked 10 years ago
- last active 10 years ago
the unit will fill.
but act’s a bit strange wehn I close the lid it stops
the unit will fill and fill but will not agitate or spin.
the lid lock will lock.
I tried to turn the tube by the belt but it will not move.
I did hear the tube try to turn but all I did hear after was a clicking noise
- Guest asked 10 years ago
- last active 10 years ago
This is a French door model. The freezer is 6 degrees and refrigerator is 54. The freezer fan is working . does this have a fan in the refrigerator ? I removed the rear section to see if it had an evaporator . It doesn’t. There is no tech sheet. Only the microscopic wiring diagram. What am I looking for here?
- Guest asked 10 years ago
- last active 10 years ago
Dryer making a squeeling noise when running? Need video on drum bearing kit on how to repair and how to gain access to the inside.
- Guest asked 10 years ago
- last active 10 years ago
THE UNIT IS COOLING WELL BUT I HAVE NO DISPALY ON THE FREEZER DOOR. NO LIGHTS NOTHING.
I NEED TO TRACE CIRCUIT BACK TO SEE IF OR WHERE I’M LOSING POWER. ANY INFO ON BOARD TEST POINTS ETC.
TX
- Guest asked 10 years ago
- last active 10 years ago
GOOD EVENING. WASHER IS SHOWING AN F07 CODE. I HAVE NEVER DEALT WITH THIS BEFORE, ANY HELP WOULD BE GREAT. THANKS, TODD FROM NY.
- Guest asked 10 years ago
- last active 10 years ago
