Repair Help

The brand in Manitowoc Ice Inc. I am not familiar with commercial icemakers, I got called out this one and I need your help. When the machine is turned on, the water will run over the vertical ice tray. The back of the tray is at zero degrees. A little ice does form on the trays edges. Also there is a cover over the vertical ice tray that opens to release the ice when in harvest. But right now when the cover is closed the water continues to run. How is the correct operation of this icemaker? Also is there a video that I could view? Thank you for your help, Ricky.

I have a no cool on fridge, condensor and evap fan running compressor cold to touch.

I have a Dacor wall oven above model #PCS130B. The unit will start beeping (NO FAULTS) when not in use.
I disconnected the key pad and it hasn’t returned. I had one of these recently and had to change the user board (on the control panel ) also.
Does anybody have the test procedure for the key pad on this unit.
Thanks in adavnce

the fridge is freezing the stuff on the door.
i have cleaned out tons of dust from the bottom and back coils i have also made the temp in the fridge higher. it was good for 2 days and now its freezing the food on the doors gain

Customer calls and says the fridge went blank after the storm. Pls send video or service manual on this beast thanks

The condenser fan is not working I’ve checked the for resistance I have zero resistance on it I have checked the start really as well I changed it to what I thought was a good one I heard a lot of shaking in it and the compressor is not turning on as well will the fan not work unless the compressor works or will the compressor not work unless the fan is working

it dose drain and spin but when it fills with water it leaks out from the bottom of the front door

I’ve open the bottom of the unit figuring it may be the belt the belt is intact when he goes into the spin cycle the pump for the drain does spin only the motor is extremely hot and none of the other belts turn I try to manually turn it to the right it will not go when I try to push the ball to the left it will go in the tub itself I can turn it either way it works smoothly

There is Frost On the coils in the back of the freezer I check the the heating sensor for continuity I’ve got a resistance reading of 200 however I check the heating element for continuity I manually put the machine into the forest and nothing happens

Hello
I am working on a Subzero two drawer unit that is not cooling. Do you have any information on diagnostics ?
Thanks

Need a tech sheet for above model of Bosch fridge. Freezer is cooling fine but fridge is not cooling at all. Want too check readings at main board for different parts instead of just putting in a bunch of new parts. Steve

I/M overfilling, I/m frosting up around it , also leaking out the dispenser

HI GUYS. THE ICE MAKER TRAY IS STUCK IN THE UPSIDE DOWN POSITION. THIS UNIT DOES NOT HAVE A RAKE, IT HAS A TRAY THAT INVERTS AND TWISTS FOR THE HARVEST. I REMOVED THE ICE MAKER AND CHECKED THE VOLTAGE FROM TAB TO TAB AT THE ON/OFF SWITCH AND IT WAS LIKE 12 VOLTS THEN DROPPED TO ZERO. SHOULD I BE CHECKING ONE TAB TO GROUND? I SAW ONE VIDEO ON YOUTUBE AND SOMEONE COMMENTED THAT THESE ICE MAKERS HAVE ALOT OF TROUBLE. ANY INFO IN ANY DIRECTION WOULD BE GREAT. THANKS, TODD FROM NY.

de-iceing circuit isn’t working refrigerator iceing up. Do you know if the circuit is part of the control board? Do you have a diagnostic sheet on this refrigerator? I would like to force the de-iceing circuit on. make sure the output is working to the heater. I know there is a sensor on defost circuit how to you test it? Do you test it with a ohm meter?

Does rubbing or knocking sound only happens when the machine is on for more than a few minutes I took the drum out and the noise disappeared I put the drum back in and I’m getting the noise I do not see anything physically wrong with the drum I suspect it may have to do with the blower or something else the drum seems find belt is fine I would appreciate you can give me some insight into this

I got the error message of f7 E5.
When I turn the machine on. I hear like the actuator or something like it that trying to move but the machine will not kicking on

When the machine goes into a high-speed spin cycle there’s a knocking sound of open the top and the back I don’t see it nothing against anything however I did see some black residue on the bottom rear near the belt I’ve also noticed when I try to turn the tub by hand that one of the top spins it looks like it is bent a bit.

freezer not freezing after two weeks – slowly loosing freezing capacity. would a replacement coil be a worth while investment. how hard is this job? fresh food refrigerator is still working

Do you have specs on resistance of the heater and the thrmostat. The de-ice in circuit isn’t working?

This is an LG built refrig with Kenmore badging. I cannot locate the water tank heating wire to replace so the water leading to the in-door icemaker can flow again. Do you have this part number or a suitable solution to fix this icemaker water supply in the door from freezing?

Samsung gas dryer heats and turns on for 2-3 minutes then shuts off flashing eo code.

When in spin mode machine goes severely unbalanced?

ohh man i feel dumb, lol. anyway dish washer was leaking from diverter valve fixed that. worked for a cycle now it will fill for a a while diverter is constantly moving like it is not sensing the proper position. but the wash motor never comes on. question is, if the diverter valve does not go into the rite potion and stop will that make the washer not start the cycle? it did have a diverter error code saved in it.