Repair Help

My electric whirlpool dryer is not heating. Any suggestions?

My Whirlpool washer is leaking water from underneath the unit, I think its coming from the pump .

My Whirlpool washer is not spinning and is making odd noises. I found plastic pieces and rubber pieces inside unit.

My GE refrigerator is not cooling properly. It has a large frost build up on the back wall…

My GE oven will not ignite.

My Kenmore washer is not spinning properly.

My GE refrigerator is not dispensing ice or water. Any suggestions?

My Hotpoint dryer is making a loud squeaking noise.

No power to gas valve. Can get dryer to heat by jumping relay at control board. All the limits are good, the thermistor is good and ohms at 1130 (at the thermistor and at the plug on control board) even have replaced thermistor and UI. The reason I tried the UI was because of the fact the dryer did heat once by repeatedly pushing dry level button and heated briefly a couple of times for a few seconds.
I have received two boards and the second one was not packaged and was clearly previously plugged in, not sure if the first one was used also, and this did come from a PD . I am now in the process of taking dryer in and giving customer a Maytag loaner until issue is resolved. I will be ordering another board from a different PD unless someone has another suggestion.

unit will wash and drain and shuts off with 8e code be for spin.

Hi, I have a Frigidaire refrigerator not making Ice. I changed the ice maker and still not making Ice, water pressure is Ok and filter recently changed. I noticed I couldn’t turn the euger motor by hand. I’ll appreciated if you could help me.

The famous LG LE code has shown itself.

The customer says that she does not get heat from the unit regardless if it’s in microwave or convention
But the unit dose have power

I’ve go a odd one the water is coming in reversed. hoses are correct. when you call for hot water comes in cold . rince water coming in hot . checked ntc, wiring to water valve, o.k. hoses not reversed. in diagnostic water will come in right but when you select cycle water is reversed. whirlpool ….Any suggestion ?

I also have a stainless outdoor vent hood by Broan (looks like most others), as noted in the User Manual. Naturally, I cannot find the sliding rheostat switch that controls the fan. The fan motor was just replaced by another servicer, and he could not find anything to work. He does not have the advantage of the PSA network, either, which is why I am asking you guys. The unit has a light/fan rotary switch, and a sliding tab to increase or decrease the voltage out. It is the rheostat I need!. Are these by any chance fairly generic?

Problems seem to come in pairs. I have a Bosch Dishwasher. The circulation pump lost the propeller so I was almost finished putting a new one in and the part that it subs to has a missing tab where the old one had one. They are numbered 1-4 and the #4 pin is missing and now I have no idea where to put the pink wire. Of coarse the customer was monkeying around, took the front off and the kick plate off and the wiring diagram is missing.
Any help would be appreciated.

the customer is saying that the oven will go on by itself from time to time

The kit # 8286320 it has 9spud-orfce colored .2white-2blue -2red 3not marked //where does each colored go .IF THERE IS A VIDEO , OR INFORMATION TO SHARE, THANK YOU

on this unit it will start only while the push to start button is held down.

This is a dishwasher and it has an unusual plumbing setup. There are two dishwashers about 24 inches from each other and they were both routed down into the basement into one trap. I am nervous if I put an air gap in place behind his counter the distance down and across will not drain fast enough and water will back up. Right now they are both siphoning and throwing an error code.
Let mw know if anyone has any ideas. Thanks

No start no led lights found bad thermostat at control board (panel) has anyone had this issue and was there an component the caused the issue ? thanks.

We went out to change the dispenser paddle on a frigidaire refrigerator. After changing it out the auger motor continuously ran. disconnected micro switch for paddles and auger motor still continuously ran. Changed out power board, still the same problem. Changed out user interface board. Still the same problem. Also Ohmed out wires inside door for possible short. This did not do this till I changed the paddles. Anyone have a direction to go in ? Thanks

My Hotpoint dryer is making a loud high pitched squeaking noise.

I NEED THE SCHAMETIC TO THIS HAIER FRIDGE, ITS A SMALL UNIT 10.? CUBIC FEET. IT HAS SOME FUSES SOME WHERE ACCORDING TO MY FRIEND BUT NEED THE BIBLE ON IT. THANKS

I sold this unit to a customer, got a call said it had filled all the way, all the way to the top, I have never seen this on this type of unit. I am thinkin g could it be the valve. control board or?????

Initial complaint: unit is working normally but board dead; cannot see display and can’t program. Installed control board: display still dead; 12vdc to ground at all 3 wires; replaced display board; same result. Had 12v at all 3 wires to display board. Am I not checking the DC voltage properly? What am I missing here. on previous calls, replacing the main board has always corrected a dead display (unless the display board was shot). Bad control board(though I’ve tried two, I’m well aware of the problems with the 942 board)? Thanks in advance for your help.

This washer is intermittantly over filling. I have cleaned the water level pressure hose and replaced the water level pressure switch. The water valve shuts off if you hit cancel or unplug the unit so it does not seem like a valve sticking open. I’m leaning toward a control board issue. Any tips on how to further test where the fault is would be greatly appreciated. Thank you

I have removed the unit a few times to dry the leak sensor but it continues to error out . I cannot pinpoint the source of the leak and usually gets through one cycle then faults and all hoses look fine and connected securely, any ideas?

I repaired the icemaker on this model but now the customer says the french door on bottom is out of alignm,ent I know i saw a video on how to align this door,pls if you can put it on here so i can get educated thanks