Repair Help

My refrigerator has twice leaked water in perhaps 1-2 months’ time, and each time it is just a small leak, perhaps 4-6 ounces each time. Would this be indicative of a frozen/plugged drain? I’d like to know that I’m going in the right direction before beginning the process shown in your video.

how do i install a ice maker in this refrigerator

After speaking with the Kenmore service and parts department, they concluded that my gas valve to bake was either clogged or broken since the broiler element works and we didn’t smell gas when we tried to use the bake control. I didn’t find a video on how to replace or clean the gas valve. We got down to the valve but don’t know where to go from there. Do we access it from the back to replace it or do it from the oven? Do you have a video

Hi i have a problem with the freezer coils freezing over with ice, the code flashes 3 but i just watched your video about the heater wrap around the freezer being replaced, the freezer drain is always frozen solid and wont drain without a lot of effort on my part to make sure it is clear, now the fridge side is getting a pool of water under the bottom drawer. looking forward to hearing from you, thanks for such a great site to come to for help!!! Ken
P.S. it is my understanding that the code means it is a sensor for the heater. ???

I Have a Whirlpool Gold French Door Refrigerator
M/N:GX5FHDXVB03 S/N:K02386807 purchased on 6/21/2010.
-The Vertical Mullion Rail (Flipper Mullion) is very warm or even hot to the touch.
-The freezer, set on the warmest setting is too cold.
-The refrigerator is not cold enough.
-After the internal controls for the refrigerator and the freezer are both set to off, the unit continues to sound like it is running. This stops only when it is unplugged.
How should I proceed?

My Kenmore dishwasher shut off in wash cycle with the bottom full of water and the electronic controller will not illuminate. There is power to the unit and no wires are loose.

Something seems bound up. The motor is making an electrical hum noise and it’s pulling alot of current (my lights are dimming). A self reseting circuit breaker soon trips after about 15 seconds of this. I flipped the unit over and the big pully would only turn in one direction. After a few rotations, it seemed free and turned in both directions. I flipped the unit back upright and plugged it in, but it still would not spin. Should I be able to spin the drum by hand? It will not turn either direction now. Any ideas what it is?

I have it turned all the way up and it’s not getting cold as it should . I have had it 9 going on ten years.

Fridgidaire (electrolux) affinity.
Error E66

Hi there and thanks for making the youtube video. I have the dryer open and the drum out. I have a multimeter but to be honest it is one of those tools I don’t really know how to use. What setting do I put it on to test the doohickeys? What am I looking for on the multimeter to determine if its bad or good?
After writing the first question on the youtube comment section I set it it the 20ohms and get a reading of 1.1 and 1.4.
Also when I took the dryer apart there was a lot of lint, coins and some other misc debris in the bottom of the dryer. Is this normal or might I have a leak somewhere?

I have similar Kenmore. Ref part started freezing food, then a few days later I saw water on ref shelves. Long story short, removed ice maker, removed back panel of freezer (may have to defrost ice a bit to free it), and then saw ice buildup in drain tray and over drain tube. Removed back of refrig to see drip pan. Then in the freezer part, used hair drier and poured hot water on the ice to melt it. Soaked water run off with towel. Continued until water flowed down drain tube. Checked in the drain pan to see the water.

THEN from what I saw on another video, added an 18 gauge cooper wire apox 12″ long to the lower heating element. There are two elements, one on top of the cooling fans and one on the bottom. These heat up during the defrost cycle to melt ice. Water drips into the drain tray and down the drain tube. Careful when working around the fans, they bend easily and cut fingers even easier.

Looped one end of wire on the left side of the lower defrost element Then looped the other end on the right side of the lower element while shaping the cooper wire down to but not touching the drain tray (C shape). This should put heat right over the drain tray and tube to help melt any ice buildup.

ALSO from what I read about one of the causes of this ice build up in the freezer, warm moist air rises in the drip tube, meats the cold freezer air, and the moisture freezes up in the drain tube causing the ice dam. So I purchased two small elbow tubes and a worm clamp. Using pipe tape, connected the two elbows into a U shape and added them to the bottom of the drip tube. Use pipe tape and clamp to secure to the bottom of the tube. When water drips from the freezer, some of it stays in the U and prevents warm moist air from rising to the heater. Similar to the U shape in plumbing to keep sewer gases out of the house. QED so far.
Show less

HELP!
We are unable to take off the drain lid and the water wont drain from the dishwasher.
We cant find any videos on your site or ytube to help us.
Can you assist, my mom is frustrated!
Thanks, a son
We have a whirlpool dishwasher

TURN ON AND IT FIRES UP THEN SLOWLY DIES OUT..CAN NOT LIGHT…

Unit will only start in diagnostic mode. When I first start diagnostic mode, all lights are green. The unit Will get a few minutes in to diagnostic mode and dies, no lights and the unit will not respond. It will only respond trying to run diagnostic mode, always get the same result, it dies and is unresponsive.

I checked to see if the chopper blade was jammed, it was not. I replaced the control board, that did not fix the issue.

Any ideas. Could it be the thermal fuse? Would diagnostic mode still try and work if the thermal fuse is bad?

I tried working through the service manual attached to the inside of the kickplate but there wasn’t anything in the troubleshooting that referenced what to look for when the unit died during the diagnostic mode.

I assume that once the unit got to somewhere in diagnostic mode that wasn’t working properly it shut down…

Any ideas or feedback would be appreciated.

I own a Maytag refrigerator Model MFI2269VEW, 2 years old. The icemaker is not making ice but water is coming through the dispenser. Since water is coming through the dispenser would it be the ice maker itself or something else? It is connected to a reverse osmosis system and the refrigerator filter is still in place. I turned the on/off switch off, then on, and the arm did work and reset but I still didn’t hear water fill icemaker mold. My wife and I haven’t used the icemaker that much the last few months.

Thanks

My evaporator fan is not running and I think has failed. I couldn’t find anything based off my model number and am going to try and replace it. I found a part number that is think is correct, could someone confirm for me? Number is 12013209Q.

My Crosley fridge is accumulating quite a bit of water inside. I don’t think it’s condensation from it not cooling, it seems cold enough, and I didn’t spill anything. Why would there be so much? Is it something I can fix? My husband thinks it quit cooling at some point and defrosted but it seems ok right now.

Our range is beeping non-stop and flashing the aforementioned error code. From what I could find online, this is a shorted keypad. So what part do I need and is there a video that could show me how? I really don’t want to have to get a new range and am hoping this won’t be too difficult.

Our dryer isn’t heating up. My husband checked the coils because I heard that was a typical repair, but they are fine and working. What else can we check?

My washer isn’t spinning out or draining. I checked the lid switch from a video I found but that seems fine. I did do a load of rugs last and am wondering if maybe something got stuck in the pump? Thanks in advance for any help on this!

when i turn on any top or oven, it will come on and die out..then i have to leave ignitor on until it comes on and stays very low flame before going to proper setting..

dryer won’t start. turn drum by hand & then push start button it will start. let go of start button it will stop.

everytime i try to wash my clothes it’ll spin once and 3 mins later it will say R-09. please help

Maytag washer starts spinning clockwise during the agitation cycle then overflows.
During the agitation cycle the tub goes from the small jerks into a fast clockwise spin.
Help?

It does everything else great but it stop throwing water in during the rinse cycle.

I had asked the question in reference to this video that oyu guys posted
https://www.youtube.com/watch?v=IEr9A7uhdN8

thanks,

Convection part of oven will work but the microwave part does not.

f6-e4
f6-e3
f9-e1
f5-e1

any help on these codes?