So I have a Frigidaire refrigerator from 2009 that seems to no longer hold a steady temp in the fridge section and even when I turn the thermostat to make it colder it will turn on for about one minute and then shut off and then 3 minutes later do the same thing over and over again. There is no ice build up in the freezer and that is holding a steady temp of around 20 degrees but will not get colder than that. The fridge side will not get colder than 40 degrees and will flutcate between 40 and 45 depending on how much we open the door. Even the coldest setting on the thermostat there in no change in the fridge temp or freezer temp as well.
- John Christiansen asked 9 years ago
- last active 9 years ago
I followed the instructions doing everything stated on your video found at this link.Everything checked out ok.
https://www.youtube.com/watch?v=OpZXoD16uvs
After doing these things the dryer ok ran for a couple days but then the thermostat reset button began popping out again. I replaced the thermostat with an OEM new one and the dryer ran ok for a couple days. Now the new thermostat button is popping out again and has to be reset. It’s happening so often that I drilled an access hole in the front of the dryer so I can just
reach in and reset the button when it pops. Any thoughts about what to do next?
- Guest asked 9 years ago
- last active 9 years ago
Customer ice dispenser makes a grinding noise when depressed. The ice dispenser works well without the noise.
- Guest asked 8 years ago
- last active 8 years ago
I have a Samsung refrigerator. This is a French door unit.
The back panel in the fresh food compartment was solid ice the evaporator fan blade was frozen half way up.
I pulled the plug defrosted the back took it out. Replaced the evaporator fan. Plugged it back in the display, located inside at top showed 88 on the freezer side of control and the fresh food side of control. The evaporator fan was not running. I did have both doors open about 3 hours and ran a steamer inside to defrost the back panel.
The settings will not respond at all and the fan is not running. Is there something I need to reset? Thanks In advance
- Fred Abernethy asked 9 years ago
- last active 9 years ago
This freezer section thawed , then rebooted and cleared has worked ok then showed h1. then before it defrosted started working again.
- Guest asked 7 years ago
- last active 7 years ago
I cannot get the ice maker to function into harvest cycle. I need help with diagnostics.
- T&G Appliance Repair asked 8 years ago
- last active 8 years ago
Need to replace the touch pad control for the water/ice dispenser. If anyone has a diagnostic manual that you would be willing to send me, I would appreciate it. Thank you.
- Fred Abernethy asked 9 years ago
- last active 9 years ago
We have a Jenn-Air/Maytag Appliances JDS9860AAP oven, which displays an F1 error code not long after reaching a preheat temp (typically 350). After clearing the error, it eventually comes back multiple times as the oven cools and has to be cleared each time as it cools its way down.
- Guest asked 8 years ago
- last active 8 years ago
i ran a diagnostic test on the washer but do not know how to interpret the codes.
code 1: F: sensing rinse done E: done
Code 2: F: sensing rinse spin done E: rinse spin done
code 3: F: sensing rinse spin done E: done
code 4: F:sensing spin E: done
Can you please tell me what this means….
The washer will not spin (makes the noise like it is spnning, the lock button flashes)
- Amber asked 10 years ago
- last active 10 years ago
How do you reset the control panel on a Maytag refrigerator, model #MFI2569YEM0 display board lights up when you touch any button beeps when you push water or ice button but no lights unless you push a button
- Fred Abernethy asked 5 years ago
- last active 5 years ago
I have a Kenmore refrigerator model number 797.77563600 on a plane video it comes up with no match I am having an error code on this refrigerator ER FF
- Guest asked 9 years ago
- last active 9 years ago
The dryer powers on but doesn’t start. Pressing the start button gives 3 beeps almost like the door isn’t closed. I put the dryer into test mode and all I get is error code EHd, this doesn’t appear in any diagnostics codes anywhere. The control panel appears to be responsive. None of the error code sheets show this error code.
There was a large amount of lint being blown out the back of the dryer and I cleaned out the outlet. I’m about to take apart the bulkhead to get to the blower and vacuum that out too.
- Guest asked 6 years ago
- last active 6 years ago
My Samsung microwave is showing an e83 filter code how do I fix it?
- Harley Clark asked 5 years ago
- last active 5 years ago
Refrigerator giving me a C4 error code.
- Patrick's Appliance Service asked 4 years ago
- last active 4 years ago
MACHINE DOES WORKS. DISPLAY “AF” ERROR CODE.ELECTRIC DRYER.
- Guest asked 6 years ago
- last active 6 years ago
I’ve watched your videos on how ice build up behind the back panel will prevent a frig from getting cold. I’ve also had to remove this build up of ice myself a total of 3 times. I noticed after the last time I removed the ice and plugged it back in my frig temp gauge would show 34 degrees but the compartment was not close to being that cold. Why would my frig not get as cold as the temp gauge even after I cleared all the ice out? Now I’m in the process of removing ice again and my question is what part do you think, based on your experience as a repair technician, I need to replace so I don’t have to do this every 2 months? I can verify that the fan is still operating properly. Would you suggest I replace the heater? Or the sensor? If I purchased the heater would the sensor also come with it? The frig is only 2 yrs 4 months old. Thanks for your help.
Art
- Art asked 10 years ago
- last active 8 years ago
Model number LFX25991ST/06 What position is the refrigerant valve in when the refrigerator is unplugged? I want to pull a vacuum and I know the Whirlpool you have to use diagnostic mode to open the 3-way valve. Is that the case with
the LG?
- Tim O. asked 9 years ago
- last active 9 years ago
the 1st steps just yield c– – f on the freezer display and 0c on refrig display when I do steps 1,2,3. it reverts back to set freezer temp and refrig temp after a few minutes. what am I doing wrong?
- r0n asked 10 years ago
- last active 10 years ago
I have examined the heating element of this Samsung dryer; but it did not appear broken. The coils were a bit black in some places but nothing broken. The inside of the dryer was filthy with lint … on the motor, in the heating element, and clogged in the lint exhaust hose. The tub spins and it has power. Is this low heat condition and indication that the heating element is going out or is there a problem with a thermostat not working correctly? What would cause a low heat condition in the dryer?
Thanks-
Fred / Lubbock, TX.
- Fred asked 10 years ago
- last active 10 years ago
it’s been leaking water for a few months now…and it frost up where once a week, i’ll have to chop off the ice frost. Is that a repair part or do i have to replace the whole ice maker assembly?
- Don asked 10 years ago
- last active 8 years ago
GE refrig model: PFSF5RKZAWW that is Dead, no display, no interior lights, no fans, no compressor.
He verified 120 v through emi filter to the main board and inverter but unit will not fire up. Pulled individual harnesses to see if something may have been shorting low voltage but no change. He did change main board and user interface with same results.
- Guest asked 9 years ago
- last active 9 years ago
The large oven tends to take a longer time to preheat, even though the hidden bake element and the broil element are cycling during the preheat. Also, should the throat elements be coming on to assist pre-heat, or are they only used to convect?
- T&G Appliance Repair asked 9 years ago
- last active 9 years ago
Refrigerator not working at all and displaying SY CE
Installed Main Control Board/Board switch kit w/ harnesses 5303918556
Took out old board, installed new, and nothing..not even error code.
Put customers old board back in, and it displays error code
Assuming I got a defective board, and purchased another one.
Re-installed new board, same thing. Nothing..not even error code.
Put customers old board back in again, and it displays error code.
Researched problem further and found out I may need to replace the board behind display on door
User Control and Display Board 241973712
Went back and installed both new boards, and still machine is not even displaying error code.
Put customers old board back in, with new display board, and error code comes up.
Everyplace I research, anytime this error occurred, tech replaced both of these boards and problem was solved.
We checked all the wiring and connections to all harnesses, and they look good.
Can someone please help me if you have experienced the same problem, and tell me how you resolved this issue?
I’m tempted to buy all new boards AGAIN, but I don’t think I could have received this many defective boards, something else has to be wrong.
Any help will be greatly appreciated, thanks in advance
- Guest asked 8 years ago
- last active 8 years ago
Customer says that they can only turn on one out of four burners. one comes on and when they attempt to activate other burners, they get intermitent flashing LED lights on readout. There are two LED readouts. one on left and one on right. after they activate the one burner and start to activate the others, the error code appears. left LED displays
” E ” and right LED displays ” 32 “. Sounds like control board but not sure.
- Guest asked 8 years ago
- last active 8 years ago
Hello I am having issues figuring out why this damper will not stay open. Here is everything I know.
Freezer temp reads at 2 degrees.
Refrigerator temp reads at 64 degrees.
The evap fan motor is running constantly.
After power cycling the machine the damper will open for (about) 60 secs and then close.
- Guest asked 6 years ago
- last active 6 years ago
Samsung RF4267HARS. First I found water in the bottom of the Refrigerator compartment and on the floor under the refrigerator. Now the food in my Flex Drawer is freezing. What should I fix or replace? I have been reading that the heaters are faulty and the drain sensor fails as well. Should I change out both while I am inside there?
- Scott asked 10 years ago
- last active 10 years ago
Maytag front load, epic z washer ( MHW6000XW2 ).
Have F6 – E1 / E2 error codes.
Board goes into diagnostic mode but stays at ( C0 ) position.
- David Sutton asked 9 years ago
- last active 8 years ago
I would like to know what this error code means and what can I do to fix it?
- Guest asked 8 years ago
- last active 8 years ago
I’ve just tried to use my broiler for the first time, even though I’ve had this oven for awhile already, and it doesn’t work correctly. It seemed to preheat, but then when I put my fish in, and set the timer, it seems to have shut off on it’s own. I started it over, did the same thing. Is cooling down and not staying on even though it says it is.
- Mary Hunt asked 9 years ago
- last active 9 years ago
