Repair Help

My GE washing machine does not spin out the close to a semi dry state. It doesn’t actually go into a spin cycle anymore. It turns but not really fast. What is the problem

Have a no fill Whirlpool dishwasher It is installed stand alone, no side panels. cabinets etc and the lower panel is missing. Need the manual if anyone has a copy

Bosch dishwasher having an issue with this dishwasher, replaced control, ran fine 3 times, now it is stopping in the middle of the cycle. does someone have a tech sheet?

I have cleaned both hose’s.
I opened the inside and checked for a bent hose it looks good.
but I keep getting the LF regardless of what water temperature

When I press the lever for the ice dispenser it doesn’t dispense ice. No sound or movement. I can hear the micro switch.

the machine will not turn or heat.
the boards work.
and the timer will count down but the unit is not turning.
I did a diagnostic test and I got f70
I changed ALL the boards that I can and I’m still getting the same issue.
the unit will not run or heat.
please advise

I have a customer with a refrigerator that is not cooling, or freezing. I replaced the board and it’s still not cooling or freezing.
Any advice or any way that I could check anything that may be wrong.

This dishwasher is leaking. It’s a slow steady drip but it does accumulate quite a bit. I looked underneath the dishwasher, and the leak appears to be coming from the diverter motor .
I removed the diverter motor and I’m wondering how is it possible for it to leak in this area. At the bottom of this motor assembly there is water stains coming from the inside of the round tube like section.
Before I buy a new one I just wanted your feedback.

I have an upcoming appointment for a dishwasher that the homeowner claims is not spraying as much water as before. Just in case it is not a clog in the spray arms I was just wondering how I would enter into the diagnostic mode. The homeowner claims she culd not read the serial number – sorry.

Ice build on evaporater right side on top probably 4,5 inch

PUT ON A NEW PRESSURE SWITCH AND STILL FLASHES E31 AND MACHINE DOESNT MOVE , ALL LIGHTS ARE ON

When I arrived the washer was full of water and clothes and they said it would not unlock. I put it in drain and spin and the unit drained and when It finished I pushed the power off button and it stopped and unlocked. Then in the diagnostic test it showed the f1e1 code. Then in the drain it would begin but just about 2 second and would quit and begin beeping and would not unlock. I would unplug it and plug it back in and press the power button and it would unlock. At times I could get it to drain then finally it would not. The diagnostic cycle would not work as it should. It would take 1 or 2 minutes before it would start diagnostics or before it would do a normal cycle fill or drain and spin. What do I do next? I thought it was the pump it self. Should I directly test it with a test cord to see it it will run or what?

Tested the white and red on J2 and read 13vdc. Replaced the fan and the unit went into defrost in the mean time. I unplugged the unit and hoped to skip the defrost and the unit begun to start a cooling cycle. The evaporator fan did not come on after about 25 minutes. I retested the J2 at the red and white, and reading was 13vdc. What am I missing?
The overheat T-stat was swelled and needs replaced. Does that affect the starting of the evaporator motor. Does the evaporator motor need the full frost pattern have to reach the over heat stat and thermistor before it senses and turns on the fan?

cabrio top loader washer i changed the stater on washer,,, and now i have a sd code ,,,witch means excessive suds or basket drag on motor ,, and since i ran washer through a cycle and did not use any laundry soap it is the basket dragging…. took the basket cap off and i can see the scraps marks on the basket the basket cap looks ok and it went back on with no problems very confusing

I have ice build up in on freezer coil and ice under crisper drawer . Has 1F code error

THE “DOOR AJAR” ALARM KEEPS SOUNDING. IT STOPPED FOR ABOUT A WEEK AND THEN CAME BACK. I CHANGED THE DOOR SWITCH WITH NO EFFECT. THE UNIT IS COOLING WELL AND THE DOOR SHUTS PROPERLY. I’M THINKING IT’S IN THE BOARD. ANY THOUGHTS WOULD BE APPRECIATED.
THANKS

nmbwholesale20124 days ago flag
(Lean washer back and turn transmission pulley in the spin direction (counter clockwise) and check for proper disengagement of brake. If brake is dragging add shim for proper spacing. Note: See service manual for proper procedure)

**THIS IS PASTED FROM ONE OF THE ABOVE DOCS.*** THANKS FOR THE QUICK RESPONSE. I’M LOOKING FOR THIS SERVICE MANUAL, CAN YOU FIND IT PLEASE?

THIS WAS A QUESTION FROM LAST WEEK AND THE RESPONSE DIDN’T GET FOLLOWED UP ON.

THERE ARE TWO BEEPS A PAUSE AND A SINGLE BEEP. VERY FAINT. I’VE SWAPPED OUT THE INVERTER AND TAKEN ONE APART. I DON’T SEE WHERE THE SOUND WOULD BE COMING FROM INSIDE THE INVERTER. NO MATTER WHICH INVERTER I INSTALL, IT MAKES THE SAME SOUND. ALSO THE CONDENSATE FAN ONLY RUNS FOR SEVERAL SECONDS AND THEN TURNS OFF. MY INITIAL THOUGHT WAS THIS WAS SOME KIND OF ERROR CODE, BUT I CAN’T FIND ANYTHING THAT CORRESPONDS TO WHAT I’M HEARING. ANY THOUGHTS ON THE POSSIBLE CAUSE?

sometimes the oven will work good and sometimes the screen says it’s on wether bake or broil. but the ignitor doesn’t evan heat up

Any suggestions / products to remove the scratch ?

Customer complained that washer would not spin or drain. When I arrived I noticed the tub had dropped down on support rods, and I need to replace them. Is there a cause other than the rods springs failing that causes this. Any assistance would be greatly appreciated. If anyone has the fast track I would appreciate that as well.

This is a nice looking GE side by side fridge. Mold is all over the styrofoam and foam stripping in the FF evaporator area. So these mold spores are blowing all around the inside of the refrigerator and you can see that they are growing wherever there is moisture in the fridge. Is this a design flaw in the unit? Has anyone else dealt with this and been successful at getting rid of it? Even if I went through all the work of replacing the Styrofoam, freon lines insulation, and foam stripping I think it will return. The temps in the fresh food section were 48 degrees. I replaced the temperature sensors in the FF section. I could not find a part number for the sensor on the evaporator but I replaced it with a WR55X10025. I’m waiting to hear back from the customer to see if the fridge cools down to normal. Evaporator fan in FF working fine. Thank you for any advise.

SAME ISSUE, NOT SPINNING OUT CORRECTLY

SAME ISSUE, NOT SPINNING OUT CORRECTLY.

THE UNIT ISN’T SPINNING OUT PROPERLY. I’M NOT ALL THAT FAMILIAR WITH THESE UNITS AND I’M NOT SURE WHAT THE ISSUE IS.

Any videos on this model replacing the motor

GAS DRYER NO HEAT THERMAL FUSE IS GOOD -IGNITER GOOD HOW DO I TEST HI LIMIT OR OTHER TSTAT
DO YOU HAVE A VIDEO ON THAT PLEASE ?????

I was out on this once, I reset unit, now the only time it works cust. has to reset it. Is it the I/m. Thanks you for your help. thanks always Jim.