Repair Help

My Kenmore washer is really loud during spin and is splashing a small amount of water on the floor.

My Maytag washer starts then quits mid cycle.

The soap dispenser on my Maytag dishwasher will not come open during wash cycle.

My Samsung dryer is making a loud clunking noise, sounds like there’s a tennis ball inside.

My Kitchenaid microwave is not coming on.

My GE microwave has no power and is completely unresponsive.

My Samsung refrigerator is displaying an E1 error code.

My Whirlpool refrigerator is leaking water. Any suggestions?

My Maytag dryer is not heating.

My gas Kenmore dryer is not heating.

My Maytag washer is not spnning.

My Kenmore dryer is not heating properly.

My Maytag dryer is not starting and is completely unresponsive.

My GE washer is leaking water, any suggestions?

modelo:MVWB880BW0
brand: Maytag
problem: leak water under bottom
I did inspection under try to find a broke hose or part,
I fill with water and wait to start, clearly water come out front center, looks main shaft.
is there a video how to change main gasket. or any video related with similar problem

ragards
morales

GOOD MORNING, SMALL ITEMS ARE GETTING CAUGHT IN THE REAR OF THE DRUM. ANY INFO WOULD HELP. THANKS, TODD FROM NY.

GOOD MORNING, I DID NOT LOOK AT THIS YET, BUT THE CUSTOMER IS TELLING ME THEIR IS WATER ON THE FLOOR IN FRONT OF THE FRIDGE. SHE DID SHUT THE WATER SUPPLY AND THE LEAK DID STOP. IS THEIR A MORE COMMON PROBLEM WITH THIS UNIT THAT WOULD CAUSE THIS? THANKS, TODD FROM NY.

Refrigerator not working at all and displaying SY CE
Installed Main Control Board/Board switch kit w/ harnesses 5303918556
Took out old board, installed new, and nothing..not even error code.
Put customers old board back in, and it displays error code

Assuming I got a defective board, and purchased another one.
Re-installed new board, same thing. Nothing..not even error code.
Put customers old board back in again, and it displays error code.

Researched problem further and found out I may need to replace the board behind display on door
User Control and Display Board 241973712
Went back and installed both new boards, and still machine is not even displaying error code.
Put customers old board back in, with new display board, and error code comes up.
Everyplace I research, anytime this error occurred, tech replaced both of these boards and problem was solved.
We checked all the wiring and connections to all harnesses, and they look good.
Can someone please help me if you have experienced the same problem, and tell me how you resolved this issue?
I’m tempted to buy all new boards AGAIN, but I don’t think I could have received this many defective boards, something else has to be wrong.
Any help will be greatly appreciated, thanks in advance

Unit compressor is running too slow replaced inverter supply is 56 hz. 5 volt where do I go, there is no manual . Thanks

I know Robert has a video i think it is on a whirlpool french door refrigerator where he demonstrated how to set it up so there are not gaps but i cannot get to it now pls see if you can guide me to it thanks

Please send me instruccion how to diagnose dumper on PDS22SCPALSS

When I punch in this model # on any site nothing shows up

i need to see how to align the bottom door on this unit./ I found it once but now i cannot find itVIDEO

ciruct barker is good but im not getting any power to the unit

Hello, I got a reply from Brian on this last week. But I’m back again. Brian sent me a service guide to help. It did. However, I can’t figure out why it’s not working.
I checked the solenoid, removed the ice maker, (the ice cube tray was full of ice) but it didn’t drop them into the tray. No ice build up in the back wall. I removed the cover to the boards. The small board in the upper right corner had a small red (lite up) bulb. It was on last week when I was there.
The service guide said that the problem was either the ice cube maker or the main board.
1. Is there a way to check these parts to see which one is bad?
2. How can I do a diagnostic test on it?
Thanks Bob

i replaced the power board hooked it up and i get HI on both the freezer and refrigerator side

all burners continue to click after burners light.

so the client has a dryer that vents 7 floors up….they thought it was the vent that was clogged and had it cleand but still will not dry good.
they now put the hose outside a window and they said it works better.
i tested the dryer with a air flow meter and got poor readings Evan outside the window.
i disconnected the hose from the dryer itself and got a good reading..
can it be the blower is failing?
and if soo how wold i fix it?

Motor was not working. Replaced. Now the motor surges up and down. What did I miss.