Repair Help

if the customer lifts the lid and closes it again it continues, sometimes. I’m assuming a lid switch for this?

Trying to do a lookup and my usual sites aren’t working, need the igniter part for this unit. Current one is not lighting at all anymore. Appreciate you guys always being willing to help me out!

I’ve checked all the main components and common issues, but think I’ve narrowed it down to the tco that neesd replaced. Possible? And do you carry it? Need to get this repair done. Thanks.

Per the customer he already replaced the icemaker and saddle valve himself but is still having issues. What else should I have on hand to get this fixed and working again for him? We don’t do many icemaker repairs and I’m trying to do him a favor by helping him out.

I found the primary water coil bad but can’t find the valve replacement information through my usual lookups. Do you guys have it or know the part information?

I was going to take the latch assembly, anything else just as a precautionary measure since I haven’t got my hands on it yet?

I got in and defrosted the evaporator but think it also needs a jazz board replaced. Anybody there have that info handy?

I’m pretty sure this will be the belt due to the customer’s description and finding pieces of rubber on the floor. Whats the part number for this?

washer model# mfw9700sq1 If I put it on any cycle, like delicates, permanent press it jumps to regular cycle. where do i start? can it be the interface? any help is appreciated

Samsung top load washer
Its a 1 year old washer that will attempt to spin at about 8 mins left in cycle, gets to about 150 rpm and then jumps back to 18 mins. and starts filling with rinse water again. There are no suds or evidence of off balance load, drains completely each time, no codes stored when put in diagnostics. the unit will spin in test mode and have done this fine with clothes in it also, although not recommended. Drains fine and spins great everytime in test mode, reaches 1050 rpm.
Previous company that worked on it replaced the inner tub and main control board, and then bailed on customer (while under warranty).
Motor, hall sensor, and wiring all ohm out correctly. Has anyone experienced the same issues? Since washer will spin fine even under load in test mode, I assume motor, wiring, and controller are good but there is another issue such as a tub sensor that is not in circuit during test mode? Any help is appreciated

I’ve replaced a non working evap fan and it cools but not to the proper temp programmed.
Kitchenaid ksc24c8yy02

The washer will without fail make it to the rinse everytime. The in use button is lit however the rinse isn’t, advancing one “tick” will put it in rinse but it does not fill, attempt to wash or advance from there. If you bypass the lid switch and advance it roughly 3 ticks it will start agitating without water or filling. If you advance it far enough (right before final spin) it will spin while adding water.

Hello,
I am trying to install a new oven control board in a Bosh wall mount oven. I get the control panel off just fine, the problem is getting the silver cover off. I removed the knobs no luck, I tried prying it off didn’t work. The only thing I see are the tabs in each corner, I tried to move those as well no luck. The screws that hold the board in place are put in from the front so I know this has to come off somehow just don’t know how.
Any help would be greatly appreciated.

Thank you,
Greg

Kenmore Elite dishwasher made by Whirlpool that will not drain properly every time. Will work 1 or 2 cycles then at the end of the 3rd cycle will leave about an inch of water in bottom of the dishwasher. Everytime I drain the dishwasher through the cancel cycle it does just fine.

Freezer evaporater fan motor not turning . He claims he checked the voltage and got only 4 v should be 12 between red and white for this units fan motor. It would not go into diagnostics for him. He’s blaming the board. We dont show this board as a very common part and I am questioning this. it. Any suggestions thanks

We had a defrost problem on a refrigerator 90 days ago. WE DEFROSTED EVAPORATOR – REPLACED EVAPORATOR THERMISTER AND MOTHER BOARD . Now we went back out for a no cool, compressor was not running cycling on and off on overload. We replaced the mother board and the compressor started running perfect amperage. The only issue now is the lights in the fresh food and freezer flicker on and off every 5- seconds. We tried a second board with same symptoms. We checked all connections and harnesses including the new thermistor we replaced. We unplugged the display thinking there may be a short with no success. Has any member seen this issues or have any suggestion on a direction to move forward ? Thanks in advance. Matt

The subject refrigerator needs new door seals. I believe you just pull the old seals out of their grooves and push the new ones in. Is it this simple or is there something else I need to be aware of? Thank you.

Microwave turns on for 2 seconds and then turns off. History: I changed out a blown fuse about six months ago but did not know at the time I should have changed the monitor switch. Last time it was dead and now it just turns on for 2 seconds. Any ideas what I should be looking for? Model #HMB5050/01 FD 9007100017 FCC ID ACLAP7A01

We really can use some advice on a Whirlpool Cabrio washer # WTW6600SG2.
Customer complaint: Set on ‘NORMAL’ the unit will fill and run in the wash cycle for about 15 mins. pause, drops to 5 mins on display, drains and spins, end of cycle.
There are NO fault codes showing or saved.The control was replaced about 1.5 years ago. The unit ran fine after the board replacement.

i have looked at ignite-rs they are good both boards have been replaced so i know it is not the board I’m at a lose as to what it could be please help thank you.

motor ohmed 11.6 on all 3 terminals.sensor ohmed out fine as per tech sheet. ran all tests all fine except basket won’t turn. can hear faint hum at motor.mostly get 3Ecode. a couple of times bE code.can the motor be bad and still ohm out perfect? also will fill half the tub till control board kicks pump on, could this be related ? thanks

We really can use some advice on a Whirlpool Cabrio washer # WTW6600SG2.
Customer complaint: Set on ‘NORMAL’ the unit will fill and run in the wash cycle for about 15 minutes. pause, drops to 5 minutes on display, drains and spins, end of cycle. There are NO fault codes showing or saved. The control was replaced about a year ago. The unit ran fine after the board replacement. This unit is located in a beach house and gets only a few months of use a year. Any help or advice would be greatly appreciated.

I have an Electrolux Gas Oven M# EI30GS55JS – and the clock display does not light up the “1” for times 10:00, 11:00 or 12:00. It only displays the last 3 digits. example is the display looks like 1:00 when it should be 11:00.
The parts diagram shows a glass cover and a separate control board. All functions for the oven work fine. I think I need to order the glass cover(part#318923502) or the control board (part# 316576703)?

I have issues with a Kenmore refrigerator model # 795 7757960 ff code unplug and re plug code reset refrigerator back to normal went on job ran diagnosis code did not appear fresh food fan okay. A day later code back again going on job plan to change fan motor any suggestions will check wiring.

I HAVE NO POWER TO THE WATER CONTROLS ON THE DOOR AND THE EVAPERATOR FAN IS NOT WORKING. REFRIGERATOR BEEPS EVERY FEW MINUTES

This washer keep vibrating a lot on spin. I noticed that each time it happens it’s on smaller loads, it seems noisier then. Is this just a weight distribution issue or something else?

All four burners are turning on when the left front burner is lit. I changed out that switch but there’s still an issue with them all coming on. What’s the deal?

I’m the only one on today and am not sure if this is just a matter of clearing the drain? Am hoping so but wasn’t sure how typical these symptoms are.