Repair Help

I think this needs the heating element replaced but I can’t find the part for it.

I found this unit to need starting components, but couldn’t find them separate from the compressor. How can I get just what I need?

Summary above is per the customer, I’m heading out there and want to take a control with me. Anybody there have the part information for me? Am pretty sure this is the issue.

I don’t have a model number on this oven. I was working in this kitchen removed the oven door improperly and could not reinstall it. I pushed the hinges and set the catches and attempted to put the door back on. After a little effort I got it back on but then could not open it. The door is locked. I have tried a coat hanger to pull on the lock without success. I have tried setting self clean and then cancelling it and turning off the circuit breaker for a few minutes. I would be very greatful for any tips on how to get the door open. Thanks

—

I feel as though I’ve checked everything on here. It’s not the heat because it’s getting plenty hot, fuse & thermostat tested fine. Control was still good, venting looked clear from inside and I checked the outdoor, even though it did seem to have some diminished air pressure it may just be due to such a long run from the laundry room. Any ideas?

GE bottom mount refrigerator section is warm freezer o.k. evap fan running damper intermittent opening. when we have it apart it opens and closes . replaced refrigerator thermistor and rear board. a head scratcher damper open when we close up ref customer calls back ref warm

This washer isn’t spinning and it seems like the clutch is the problem. It looks like from the diagram that it’s an entire housing assembly, is that right?

I’m pretty sure this is a tub boot, but I’m having a heck of a time finding the info for it. Would really appreciate some help if you have a minute.

Having issue with this LG made Kenmore. No tech sheet, evap fan motor is running all the time…tech was thinking that the relay on the board was bad. Any thoughts?

F11 fault code no tech sheet in washer any help appreciated

I cleared the defrost drain and replaced the defrost sensor thinking and hoping that would work but am still getting some water now a few days later. Am I missing something?

I think it’s the belt but am unsure how to even get to it. Possible idler pulley too that I may need to take with me just in case.

This dishwasher was just re-installed after a kitchen remodel. I got called out because it wasn’t draining. I removed the knockout from the disposal the first time thinking that was the issue. Turns out it wasn’t, still having issues. This time I’m getting a bad pump but cannot find the part number anywhere. Somebody there able to look it up for me?

Does this come with some kind of kit for the entire assembly? I think I need the valve and knob for it. Thanks for any information you can get me.

The washer won’t lock and actually start, just has a buzzing/ticking noise. I think it’s the door lock but can’t find the part information or a repair video for it. Any help?

We nee your suggestion regarding repair of Subzero,mod.#650/F,
,freezer on the bottom,17 years old.
The problem is the drain hose broke off in the fresh food section
by the wall and we are not sure how can we replace a hose without removing
the whole unit from the cabinet .We are going to install a drain heater (add-on),but it’s pretty simple.
If someone has experience how to replace this hose without removing a fridge,
please let me know
Thank you in advance

A few years old. FE code. Fill error. Checked all fill solenoids they were
good, put in new pressure switch and machine behaved better. I
watched it for 15 minutes and left. Five minutes
after I leave I get a text that the FE is back(happened in rinse cycle).
Anyone know these better than I do?
.

Frigidaire upright freezer control on door had an “8” and was not running. Unplugged freezer and it worked again. I suspect it was flashing “E” and “8”. I checked servicetips.com service manual, file name ends with 5995531505. It says E8 is a shorted thermistor. Do I need to go back and check this? Is replacing the thermistor the only part needed or is there a pcb/control (besides the one in the door) needing to be replaced?
I need some feedback from someone who has more experience with these freezers.

Have a Frigidare dryer today I have not seen before and no wire diagram .
Any one have a manual of this dryer, Console looks like a Cabrio.
FRIGIDAIRE DRYER MODEL ,
It’s a Frigidare dryer with drum rollers but not the one with the 3 coil element.

I have a 2 drawer Subzero ref that will run for about 3 seconds and shut off. If I plug in with
top drawer unplugged unit will run and stay running until you plug the cable back in. All three
thermistors are good, evaporator was changed a year or so back and has a good frost
pattern currently. Touch pad checks good. No visible bad spots on either board.
So does anybody have any input on which of the two expensive boards is bad?

I start a load and the rinse light comes on and then the done light. I tried several times to activate diagnostic cycle and all I could get was the rinse light to come on. I am thinking a defective electronic control. Thank you for your help

Refrigerator quits running and gets warm. Consumer hits it on the side with his hand and it starts up again and works fine for three or four days. Any thoughts as to what I should replace will be appreciated. Thank you.

WM2455HW
A few years old. FE code. Fill error. Checked all fill solenoids/ checked good, put in new pressure switch and machine behaved better. five minutes after I leave I get a text that the FE is back(happened in rinse cycle).
Anyone know these better than I do?

The bottom section of the FF is not cooling “I assume the drawers” is not cooling properly…

When customer programs MW say for 60 seconds, it starts counting down 59 58 57 56 55 . When that happens, it quits heating and shuts off. He will cancel, and after a few seconds of heating and counting down, it stops heating and the count down just stays there.

We smelled a burning rubber smell and that when she opened the door smoke billowed out. It wasn’t anything to do with the laundry. Any thoughts as to what this could be?

Excessive steam coming through vent at top of door, accumulating and dripping on floor.
Anyone seen this? Ni filter or damper door, just a duct that lets steam out.

One of our techs is having an issue with a Samsung DW model listed above, the unit fills up, then drains, then fills and then the following lights start flashing all at once (Normal, Heavy and Quick lights). Customers complaint was unit making grinding noise and would not clean, but the pump never starts up. The tech disassembled the top of the sump and no debris was found and the impellar turns freely. Any help would be greatly appreciated.

How does one adjust the water fill level on this ice maker? Thank you for your replies.

Checked the inlet valves, hoses, made sure I had water to the unit – it all looks good. Am now wondering if there’s an issue with the drain pump that is causing the unit not to start a cycle at all because the customer says it hasn’t been going into drain by itself, she was manually making it. What’s the part information for the pump if I do end up needing that?