Repair Help

I need to replace the fresh food evaporator fan motor and I’m having trouble removing the access panel to the motor.
Thanks for any help you can give me!
Charley

Water line freezes up.

THE COMPRESSOR IS RUNNING AT -1.7inHg. NEITHER EVAPORATOR FAN IS RUNNING AND IT’S NOT COOLING. I HAVEN’T WORKED A LOT ON THESE VARIABLE SPEED UNITS. I GUESS I NEED TO FIND THE DIAGNOSTIC SHEETS AND WHAT EVERY ELSE YOU COULD DIG UP. TX

The controls on this refrigerator are doing strange things like when the dispenser is pushed the alarm sounds,or when pushing the freezer temp buttons the dispenser door opens and closes. When any button is pushed all the display LEDs lite, and the compressor and fans will not run. I am also not able to locate the wiring diagram. I have replaced the user interface pad and board to achieve the same end result I started with. Any help would be great.

it seems that the microwave needs a new mag tube and diode.

Wolf Electric oven sometimes flashes error and stops baking. It’s a double oven with gas burners on top I didn’t witness the issue even though I try to re-create it but the customer says that it flashes error a number of times and then shuts off completely sometimes during preheat I’m Assuming the number of times is the error code? Do you guys have an error code sheet for this or any of the wolf models?

when this happened i tapped on the right pressure switch and it would fill. i replaced switch and it still happens also when it does fill it only fills halfway. this only happens on rinse, works fine during wash cycle

in some refrigerators and replaced compressors, evaporators, condensers … the internal leak I think is a common problem of these refrigerators

there was a power outage, then when power came back on. Refrigerator didn’t work and front display blank

freezer staying at 26 deg. fresh food at 34 deg. replaced main control board after finding only 3 volts d.c. on the inverter input from main control board.

Follow up on answer.

refrigerator stop working and just blink the front control board light come on inside the fridge fan inside is dead compressor is dead any idea help just display 888 888 on panel tanks

During agitation shifter doesn’t work and inner tub and agitator turn at same time.What is shifter voltage and resistance ? The inverter on the motor supply it’s voltage but what timer signal calls for it to actuate? Could my timer be bad or the motor or the shifter. Can you send me a theory of operation ?

the stove top sparks are not working I did not hear anything at any burner that I try.
I will light only with a match

it is an electric dryer.
the drum turns but will not heat

I have been searching for different models of appliances and all I get is, videos not available, for example, model WRX735SDBM00 videos not available. And another is an LG model LFX31925ST-OO. When I am out on a job with a not cooling problem, I need help then.Please get back to me.
Thank You, Jim.

The unit will not power up I need the tech sheet and wiring diagram. 240vac ok and neutral line. Is it the I or main control? Or both?

GE cooktop that doesn’t stop ingniting. We have replaced the spark module and the wire harness switches, problem continues. Any suggestions as to what it could be?

We have a washer that displays: ”washer did not spin due to a continous unbalance”. There is no error code displayed. When spin cycle starts it doesn’t sound like there is anything unbalaced. Any suggestions on where to start?

Washer agitates in test mode without load. When load is present washer will not agitate however, will spin. A buzzing type sound occurs when it attempts to agatate under load. A new transmission was installed by a previous service company. It did NOT correct the problem. Tech mode indicates an ERROR code: PC 1. I would like to install the correct part to fix this issue and not look like an idiot. I trust you can help me?
Thanks,
SCOTT

the lid is closed but i am still getting the LO error

Oven works but no burners on top do. Are they controled by the oven control somehow or what else could cause all of them to quit?

I have a dishwasher that powers on and when you hit start it counts down lines go across the screen it sits for around 1 min and powers down any thoughts?

Regards!
The problem with the refrigerator is that the evaporator fan motor is not working because it does not reach 120 volts. When you check with the voltmeter the voltage that reaches you is around 22 volts. I Check the electrical diagram that is located on the bottom of the refrigerator and the 120 volts leaves the Beta Control terminal J1-6 and also indicates on a “Beta Codes” that has the refrigerator by
example, the first one indicates “2” Flashing- Open Thermistor. Ok, what I want to know is how to provoke the exercise so that the refrigerator makes the self-diagnostic. I already checked the 2 sensors and they gave me around 8 and 9 ohms and I gave them heat with a blower and both sensors changed from ohms to 3 y 4 ohms.

GE Profile dishwasher about 9 years old. The keypad is not lighting up or responding to the basic wash cycles. Heat Dry and Normal are the only lights that work on the keypad.

Appliance has been unplugged and elect outlet checked. Thoughts?

Hello, Please read the Question carefully. This top load washer is about 5yrs old. Goes off balance almost every load. The Ue code will show. Start a cycle, it fills ,agitates, then after a few minutes starts spinning in one direction with water in the tub. Bang, Bang, Bang. Stops and starts agitating again. Bangs with clothes or no clothes. When it is in a spin cycle, after a while UE shows up even with no clothes in it. The tub bearings are good. The tub nut is tight. The rotor is not loose. Can hear water in the balance ring. Washer is level. Had one do this in the past, I changed the suspension rods. Still did the same thing. I asked this same question 2Yrs ago. suggested change control & rotor before 2014, and rotor only after 2014. This doesnt sound right for the problem I’m having. Then look at a video where you use rubber bands. Please, I need real help. This is a real common problem, I have seen 10 LG washers doing this. I dont know exactly what is causing the problem. The washer worked ok for 5yrs. Customer is not loading it improperly. When you come up with a solution please explain how or why this solution will fix the problem. Thank You, Jim

The icemaker a Samsung, stalls out in the harvest position as if the heater is not working. Is there any repair on this item? The part number is WR30X10131

Door does not lock

I checked the ohms on this temp probe and it read 1080. I was told that it should read at least 1100 at room temperature.
Is the probe ” bad ” at a 1080 reading “
Would it cause a delay in raising the oven temperature to 350 at set temperature? A delay of 30 minutes and the oven never reached its set temperature. Plus, when the temperature rose to about 310* it began to drop gradually to 295*