Repair Help

My GE oven is taking longer than normal to heat up.

My GE oven is not heating properly.

There is water leaking from the back of the refrigerator.

Ther freezer section is not cooling properly in my LG refrigerator.

The door is not closing properly on my LG refrigerator.

My LG refrigerator is making a grinding noise when dispensing ice.

I am not getting any water out of my LG refrigerator.

During the last load of wash the machine became off balance during the spin cycle. Not sure if it finished cycle before quitting but it appears that It was very close to finishing or did finish the cycle. Was able to empty the items in washer into the dryer as normal. Now the washing machine will not start in any cycle and yes there is power to the plug. I believe there is an off-balance safety mechanism tied in with the lid switch but not positive. Hoping possibly just a fuse or something. I cannot find YouTube help for my particular model but a similar model mentions raising the lid until you hear a loud click. I’ve done that, no click. I tried to raise top off washer so I can get to the lid switch. Again not exactly the same model as in YouTube help but I can’t get the top of washer to come up so I can get to switch. I couldn’t find anything at appliancevideos.com for this particular model. Can you direct me to somewhere where I can get help? Hard to even find an appliance repair person around my area. Would like to think I could do this myself. In search of any other troubleshooting thoughts you may have. Thanks, Tim

DRY WILL NOT START, HAVE CHECKED ALL OF THE THERMAL FUSES, PUSH TO START SWITCH, TIMER AND DOOR SWITCH, (REPLACED THE DOOR SWITCH BECAUSE IT WAS STAYING CLOSED AT ALL TIMES), EVERY THING CHECKED OUT OK. I REPLACED THE TIMER WITH A NEW ONE JUST TO SEE IF THAT WOULD HELP, NOTHING. SO I THOUGHT NOTHING LEFT BUT THE MOTOR, NEW MOTOR STILL NO START.
THIS IS WHERE IT GETS GOOD, IF I DISCONNECT THE START SWITCH AND CHECK THE TWO LIGHT BLUE WIRE THAT THE WIRING DIAGRAM SHOW IS THE WIRES THAT ARE IN THE START CIRCUIT, I GET 120V FROM EACH WIRE.
SHOULDN’T I ONLY GET 120V FROM ONE WIRE, (POWER COMES IN ON ONE WIRE, PUSH START SWITCH AND POWER THEN GO THOUGH TOTHE OTHER WIRE. ) YET I AM GETTING 120 ON BOTH WIRE ALL THE TIME. DO I HAVE A DEAD GROUND SOMEWHERE? WHAT ELSE CAN I DO TO DIAGNOSE THE PROBLEM . THANKS

Hey I have a all in one washer dyer combo that is not drying the clothes. I replaced the drain pump and cold water inlet valve (all four). The clothes come out hot but soaking wet. The dyer works by putting hot air in the drum then running that hot air over an evaporation coil to remove the moisture. Then that water is drained. Then it puts more hot water in the drum again and starts the process over. Can you give me a parts list of possible bad components to try switching out sorted most likely to least likely?

Dishwasher leaking by bottom corners of door
How do I fix this?

The water pressure on my refrigerator is very low.

My LG refrigerator is not making ice.

There is frost building up inside my LG refrigerator.

My LG refrigerator is leaking water.

Our top load speed queen washer will spin like a champ, but doesn’t agitate. Based on the little bit of testing I have done I can get it to agitate when I manually pull the belt the opposite direction that the motor spins while in the spin cycle. How do I test to see if the motor is the problem or if the timer is not sending the voltage to tell the motor to spin the the correct direction to agitate? I’m guessing that the timer sends voltage during the spin cycle to spin in one direction and then during the agitation cycle to have the motor spin in the opposite direction. Or is there a secondary switch that tells the motor to go the opposite direction? Thanks for the help.

When I first arrived the lock led was flashing like the control was locked. I cleared it but it still would not respond. Then the heated dry began flashing.
Is this a problem with a stuck pad?
What else could it be?
I need a tech sheet and service manual.

How do I put this refrigerator into manual defrost?

Machine would start cycle and go down to about 9min. At this time machine would go back to 18 min. Machine generated and 8C2 error code which indicates the mems sensor or vibration sensor and a ub error code. I tested the drum and pushed down on it and thought it was the suspension. I replaced the suspension all four suspension rod and the machine started spinning when it is empty. Then when tested with an actual load machine does the same thing it times down to 9 min and then jumps back to 18 min. Now its only displaying a Ub error code . Should i go ahead and replace the mems sensor or any ideas on how i should proceed.
Model no. WA52J8700AP/A2
Serial no. 0E6H5AEH303210J

doesn’t set any codes

How to get water automatically in the Ice Maker?
Is the user interface display related to this problem?
Which specific part is responsible to send the signal to the core control board so the ice maker can be filled up?
Does the ice maker sends the signal to the core control board to be filled with water?
How does it work?

i just sign up so i can fix cooktop
pgp986set5ss
i need to replace WB19T10085 gas vaulve
Cand find anything on this
I dont have Serial Number today

My LG refrigerator is not cooling in the freezer section

My LG refrigerator will not cool in the freezer section.

My GE refrigerator will not turn on or do anything at all.

There is frost building up inside of my GE refrigerator.

My GE refrigerator is not cooling in the freezer section.