My Whirlpool range is displaying a f3 error code
- Fred Abernethy asked 9 years ago
- last active 9 years ago
My dishwasher will not drain the water out of it.
- Fred Abernethy asked 9 years ago
- last active 9 years ago
The door on my LG washer is not closing properly
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
My Maytag refrigerator is not cooling properly.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
My LG washer is displaying a PE error code.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
My Kitchenaid stove has streaks in between the glass
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
My Kitchenaid dishwasher will not turn on
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
The water will not drain out of my Fisher & Paykel washer.
- Harley Clark asked 9 years ago
- last active 9 years ago
My Samsung refrigerator is displaying an error code and I don’t know what it means.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
The convection fan in my Samsung range will not work.
- Fred Abernethy asked 9 years ago
- last active 9 years ago
My Whirlpool dryer is not heating properly. Any suggestions to fix this issue would be appreciated.
- Fred Abernethy asked 9 years ago
- last active 9 years ago
My Estate refrigerator is not cooling properly.
- Curtis Appliance Repair asked 9 years ago
- last active 9 years ago
We are servicing an oven that after an hour it turns off. We already replaced the tempeture sensor and it’s still doing the same thing, any idea what it could be?
- mytechjoe asked 9 years ago
- last active 9 years ago
There is frost building up in the freezer section. what can i do to rectify this issue?
- Patrick's Appliance Service asked 9 years ago
- last active 9 years ago
My Samsung dryer is making loud high-pitched noises.
- Harley Clark asked 9 years ago
- last active 9 years ago
One of the burners on my viking stove will not light
- Fred Abernethy asked 9 years ago
- last active 9 years ago
The clothes are still coming out of the dryer wet.
- Fred Abernethy asked 9 years ago
- last active 9 years ago
Fridge too warm freezer cold
- Guest asked 9 years ago
- last active 9 years ago
We are servicing a Kenmore dryer that when turned off all lights turn on and a beeping noise starts. Any ideas of what could be causing this, where to start looking?
- mytechjoe asked 9 years ago
- last active 9 years ago
CUSTOMER STATES ICE IS MELTING IN THE ICE BIN. BOTTOM FREEZER IS -3. FRIDGE IS 34. AIR COMING FROM ICE MAKER TO BIN FROM VENT IS ABOUT 16 AS BEST I CAN TELL.
WE TRIED SEVERAL THINGS FOR MAIN COMPLAINT OF FREEZER NOT COOLING ENOUGH. EVAP KIT, ALL THE ELECTRONIC CONTROL BOARDS. STILL WEAK COOLING. FINALLY NO COOLING AT ALL AND WE FOUND BURNT WIRES ON COMPRESSOR CONTROL MODULE. WE REPLACED THAT AND COMPRESSOR STARTED WORKING AND TEMP IN FREEZER IS NOW -3.
SO FREEZER APPEARS TO BE OK BUT ICE IN THE BIN IS MELTIN.
THANKS, GEORGE
- triadapp asked 9 years ago
- last active 9 years ago
We are servicing a Bosh dishwasher that stays stuck on the last minute of the cycle and water remains in the dishwasher. Any suggestions where to start?
- mytechjoe asked 9 years ago
- last active 9 years ago
In September I found the drain frozen, I thought because of the freezer door would stay agar. I adjusted the door and deiced the drain and the ice room fan. The unit worked till November 27. I returned and found the Ice room fan frozen and the ice maker not making ice again and the drain frozen. The freezer door and gasket is fine this time. There was even ice frozen on the back outside of the refrigerator where the ice room drain is. It is very rusted. What causes this to reoccur like this? What can I do to repair this for good?
- Guest asked 9 years ago
- last active 9 years ago
there is power comeing to the unit.
and it goes to the computer board.
but then it stops.
I do not get any fans and light.
no display on the door water dispenser.
we are not getting any power
- Guest asked 9 years ago
- last active 9 years ago
the unit is getting power.
however the display and buttons to start or select do not respond.
it remains blank
- Guest asked 9 years ago
- last active 9 years ago
The washer works in any mode, until spin cycle. It will agitate, but stops every time when it gets to spin cycle. The washer was locked, stopped, and would not turn on again. What is causing this?
- Apache Warrior asked 9 years ago
- last active 9 years ago
