Repair Help

I have a maytag gas dryer that will work spuratically. You can put a load in and it will dry in a noemal amount of time but if you open the door durning cycle it may not work the next time. It will tumble the clothes but will not heat up. Sometimes you can open the door and restart and it will be fine. I have taken back off cleaned all the lint out which there was no buildup. I have also tested most components but as I said I am not certain when I test them if it is failing at that time since it works when it wants to. I ran the unit for a couple hours trying to get it to fail and never did runing it through cycles stoping and re starting with no fail. My wife tried it an hour later and it wouldn’t work. I tried and it twice and it fired up. Any idea what the problem may be? Best I can determine is the coil

Running water at fountain center at approx. 15min. intervals. Shut I/M and problem stops. Anyone? Older refrigerator.
Thanks,

The oven does not reach temp sensor 1100 at room temp. Also one of the sealed. burner is lifting on high/ lite. Position. But goes out altogether on simmer. Spark runs all time.

I replaced the ice maker in this Amana refrigerator. Since replacing, cubes are not hardening, ice is clumping in the bin because water not completely frozen when harvested. Temp in freezer is zero. The Amana ice maker part number changed to the DQ model. I transfered over all the parts to the new model. I’m thinking the harvesting is happening to soon or the heater is on to long. The ice maker did not harvest any ice in the first 24 hours and the cubes were frozen toward the evaporator but not completely frozen to the front of the unit. Any ideas on whether I should try a second ice maker or what to look for? Thanks for your help.

My Whirlpool washer will not fill with water and not agitating.

This is a new one for me. The above fridge is a french door type with the TV monitor, Pandora, and such. Problem is the drawer above the freezer has no lights shining that would turn on when the freezer were to be opened and the touch panel on this deli drawer is unresponsive. Everything else is working in the fridge.All other lights and it is cooling. Best buy told the customer that the rear main control board would need to be replaced. What say you? Thank you for any advise.

My Fisher & Paykel Washer will not drain or go into any other cycles.

Whirlpool’s newest top load VMW washer with the flat drive belt, actuator, had this one a couple of weeks back. Machine hums only, won’t spin or agitate. With top open (lid closed) in agitation, I could spin the wash plate and motor would agitate in one direction, pulsating on and off in same direction. Could only get a reading of 90VAC at motor, but could not tell if that quick pulse was 120V or not, tried with both analog and digital meters.
Tested the run capacitor on motor with analog meter and the meter showed a quick deflection each time I reversed the leads which in the past would confirm the cap. was good, at least on microwave capacitors in the past.
I ordered motor and capacitor for this machine, although was a tough sell if it was truly the motor, repair vs. new. On return trip I installed the capacitor first, and that was the fix!

My GE washer overflows when in use.

My LG washer is making loud noises.

It a 2010 unit and customers states that it will start, go thru the sensing cycle and then not advance anymore. Tub sometimes may be slowly turning. Lid lock light will be blinking. Sometimes she is able to unplug washer and restart, then it will work. If she is able to get it started, at the end it has not spun out. Water will be drained. Thinking lid lock issue here.
Checked fault codes – none. Ran it thru automatic test cycle. Everything worked. Tub turns freely and moves freely. Lifts freely. With nothing to lose, decided to run calibration cycle. After 10 minutes, it still had not finished and the lid lock light was blinking. Beginning to think it’s a control board issue now.
I don’t see this machine too much to become an expert on it. Seems when I do, it’s always something new.
Thanks.

My Frigidaire range is not getting up to or maintaining the proper temperature

The washer is producing a suds and f35 error I replaced the pressure switch w10415587. Any suggestions ? I arrived washer was putting up a f35 and suds error. I opened up and made sure the coin catch in the pump was clear there was nothing in the catch in the pump. I replaced the switch w10415587 I don’t have the f 35 error anymore however the suds error is still there. Any assistance would be appreciated.

My Whirlpool refrigerator is not dispensing water.

My Amana washer will not start, just makes a humming noise.

I have a defrost error, refrigerator temps fluctuate from 36-57 degrees.
Where can you guys point me?
Thanks,

We have a Dacor wall oven. This oven had faulted and displayed F1. According to paperwork with the unit was a relay fault.
We replaced the relay board.
We cycled the oven at 350. then switched to High broil for 10 mins. The problem didn’t reoccur.
The customer called over the weekend and said it faulted and displayed F1 again later that night.
We went back out to recheck it. The customer had the breaker off to the unit. I cycled the unit at 350 and 400 and switched to high broil again for 10 mins. The problem did not come back.
So I disconnected the membrane switch. We left the unit with the clock blinking and membrane disconnected. Called the customer next day the fault had not come back. I ordered the membrane, before part arrived the customer called to let us know the fault came, back 2 days later!
The ERC has got to be the problem. I hate to tell the customer thy have to replace both parts. Is this common for for Dacor? Any help is greatly appreciated…

—

My electric Kenmore dryer is not heating.

The holder bracket that is mounted to the left or outside wall that holds the auger motor plate has broken and doesn’t show in the parts breakdown.
Anyone out there to help me?
Thanks,

First unit MVWB755DW0 / C51840896 * complaint : it will start , lid locks , but no water enters then it skips between sense and wash then turns itself off after several minutes. ** replaced control and it operated 5-6 loads then back to the original complaint. 2nd attempt I replaced wiring harnesses , coil assembly and slide kit * worked for 2 loads then same old complaint *** 2ND UNIT * WTW7300DW / C54073584 * LG error * brand new machine with drain hose going into wash tub * plz talk it over with guys and let me know whenever you have an opportunity. Thank you as always .

F11 ERROR CODE—-NO TECH SHEET WITH WASHER—–ANY SUGGESTIONS?
it is giving the code within the 1st 15-20 seconds

Unit will power up and door will lock but then unit shows ERR and does nothing no matter what setting. Please advise.

I FEEL THE AIR VENTS. NOTHING.
THE REAR COILS ARE NOT FROZEN.
I REPLACED THE FREEZER FAN.
I REPLACED THE MOTHERBOARD BASED ON ADVISE FROM REPAIR COMPANY.
THIS THING IS EXPENSIVE
I WANT TO CORRECT THE PROBLEM.
THE FANS ARE MOVING.
I ORDERED THE CONTROLLER BOARD FROM AMAZON.
INSTALLED.
IN TEST MODE THE AIR MOVES.
OUT OF TEST MODE THE AIR DOES NOT MOVE.
I HAVE NEVER HEARD OF FREON LEAK EVER.
I DONT KNOW \
ADVISE

hi…i have a ge top load washer …it will not start..dead…i thought maybe the gfi plug…but i plugged it into another source and it still will not start….i did reset the gfi and when i plugged it back in i heard a pop…..not good i know, but i do not know where to start to check it out…..is it fused?? or do you think something else is blown?

this is what i found elsewhere?? just an fyi…not sure what to think…

Cause 1 Thermal Fuse

If the washer overheats, the thermal fuse will blow. If the line fuse blows, the washer won’t start. To determine if the thermal fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. In addition, you should investigate and resolve the problem that caused the fuse to blow. If you don’t resolve the underlying issue, the new fuse will blow too.

Cause 2 Main Control Board

The main control board might be defective. However, the main control board is rarely at fault for this symptom. Before replacing the main control board, first check all of the more commonly defective parts.

The center panel of my whirlpool refrigerator is hot to the touch.

The coils in the freezer section of my whirlpool refrigerator are frosting up

My GE oven is not heating and there is a burnt spot on the bottom element.

My Frigidaire refrigerator is not getting water to the ice maker.

My Bosch dishwasher is not heating and wont stop running.

My Whirlpool dryer is making a loud thumping noise.