Repair Help

it’s really loud on spin and I’m wondering if you guys do this repair a lot or if it’s worth it? Not sure if I should just buy new or not at this point?

Still getting water to it, I checked the line, not sure what the problem is here.

Haven’t done much looking on here but need some help fixing this leak

It goes through every cycle but the one we need, the wash!

Panasonic Inverter Microwave, Model: NN-SD277BR

Model is fairly beefy (1100W) over-the-range (OTR) style, with venting slots along upper edge.

Ran fine for 5 years. Boiled some water on the stove for pasta, so front face of microwave was moist with condensation. Started microwave and immediately started to spark from upper right side, could see it through the venting slot right above control panel. Electrical burning smell. Thought it was shorting due to moisture from the boiling water. Stopped it after about 3 seconds and ran the exhaust fan on Turbo mode for about an hour. Worked fine after that for about 3 weeks.

Happened again today after about 10 seconds. Smelly smoke filled the kitchen. Stopped it and opened all the windows, lit candles, and ran the fan again. Lights all work, did not trip the main fuse. Picture showing microwave follows. Sparking was seen visually through the venting slots above the word “Panasonic”: https://www.dropbox.com/s/jkeiezzf9u7i8z2/20141221_111315.jpg?dl=0

Expensive microwave to only last 5 years. My parents old 600W Kenmore is getting on 30 years now and works perfectly.

We just moved into this house and the drain hose sees to be very far down the pipe, what is the recommended length? It occasionally throws an error code and I’m wondering if it’s related to this.

Not sure what’s happened to our dishwasher door, it seems to not really ease open like it used to.

this gas dryer isn’t getting hot, I’ve done the coils and idler pulley myself recently so not sure where to go from here.

the display on our stove keep doing this and I don’t live near any repair services that are reputable. What is the problem? I want to fix it myself.

Not sure what specific part would fix this but need to get it working as soon as possible for the holiday.

Hi!
The problem is the following:
1. After turning on of a refrigerator, it works for ~2 hours, temp. goes down to -20 and +5 in freezer and cooling chamber, compressor stops
2. Then, after 10-15 minutes, it tries to start for 8-10 seconds, producing loud clicks and then stops. Freezer fan is working all the time.
3. Temp. goes up to +10 in both cameras, producing A1 or A2 alert.
If I give him a rest for 4-5 hours, this cycle repeats.
But some times (I don’t know why) this scheme breaks – compressor works (normally?), but temp. in cooling chamber rises up +10, meanwhile temp. in freezer drops to -26-27.
Thus, there is strange behavior – sometimes it seems to make vacuum in freezer, after the door is closed.

I turned off the refrigerator because I had ice build up on the bottom of the freezer. I tried to turn it on a few hours later and it would not start. It beeped and did not turn on. Now it doesn’t stop beeping and the display is turned off.

Error code appeared after a power outage. I was not aware of what they were, so I just unplugged unit and plugged it back in. Later, I realized oven would not light. I did NOT write down the error code. I need to see it again to begin to diagnose problem. Is there someway to make it reappear? It does not show up when I try to start oven.

CHANGE HV BOARD, DISPLAY BOARD AND TOUCHPAD NO RESPONSE REFRIGERATOR HAS IN LIGHTS BUT DOESN’T WORKS

Is this something I could do myself? Wasn’t sure how to access it.

I also got it apart a bit and a couple tub shocks seem to be not working correctly.

Some of the buttons on the touch pad work, and others don’t. Is this a faulty front touch pad or the control board behind it? Was thinking about giving it a go myself if possible.

we can’t figure out what the issue is, I think it’s some type of control issue based on what I’ve found online but not sure.

Why do my dishes seem to not get completely dry like my older model I had for years? Really bugging me that I have to hand dry some items even after a “heat dry” is on.

MY WASHER FILL BUT DON’T WASH FILL LIGHT COME ON NO MOVEMENT OF AGITATION. WHEN PUT ON DRAIN AND SPIN IT’S WORK (DRIVE MOTOR DUMP MOTOR WORK DRUM SPINS.)

MY WASHER FILL BUT DON’T WASH FILL LIGHT COME ON NO MOVEMENT OF AGITATION. WHEN PUT ON DRAIN AND SPIN IT’S WORK (DRIVE MOTOR DUMP MOTOR WORK DRUM SPINS.)

Sometimes it works fine and other days we can’t get it to kick on and heat up

I checked the venting, element and thermal fuse per some other threads I found on here. Still won’t work right. What else can I look for?

ok. so I goo to repair videos.type in the above model #. click on tech sheet and it won’t give it to me. what am I doing wrong?