A service manual would help and any videos.
- Guest asked 6 years ago
- last active 6 years ago
The controls on my GE oven are not working properly.
- T&G Appliance Repair asked 6 years ago
- last active 6 years ago
The door on my Whirlpool range will not close properly.
- David Sutton asked 6 years ago
- last active 6 years ago
Small left oven after a couple minutes of baking in any mode the clean light comes on steady and oven light Flashes three times. The cooling fan seem to be running fine from what I can hear and I looked at the big relay at the bottom of the oven for the small left oven that is having the problems and they look to be in perfect condition and all its connectors. Can I please have a diagnostic manual that will tell me what the flashes mean?
- Guest asked 6 years ago
- last active 6 years ago
My Estate refrigerator is not cooling properly.
- Patrick's Appliance Service asked 8 years ago
- last active 8 years ago
Two weeks agp the oven would shut off in the middle of baking, and now it doesn.t even start to bake.
Thank u.
- Guest asked 8 years ago
- last active 8 years ago
Thermador
- Guest asked 6 years ago
- last active 6 years ago
Unit has new pressure sensor, clean working pump, clean connection at tub to pressure sensor, good wiring, good pressure hose, clean working water valves, good drain system/stand pipe. Need to know how to narrow and what electrical readings to expect at ccu. what sequence to use at ccu to verify electrical readings. Thanks in advance for any advice.
- Guest asked 8 years ago
- last active 8 years ago
I recieving an error code F dy and cannot find what it means or is referring to
- mikjanes asked 3 years ago
- last active 3 years ago
I’ve placed a load of laundry in our GE dryer, selected a setting and when I push the ‘start’ button, the digital display shows a flashing light next to the ‘Sensor’ panel and dryer doesn’t engage.
- Guest asked 1 year ago
- last active 1 year ago
Good Evening Matt, do you have the service manual for this unit. Has an e84 error code, customer states they hear a pop noise before the code displays.
Thanks
- Guest asked 8 years ago
- last active 8 years ago
my LG dryer is not heating properly. Do you have any suggestions to resolve this issue?
- Fred Abernethy asked 7 years ago
- last active 7 years ago
The icemaker was replaced on this unit however it is still not producing ice it only works when the test button is pressed
air temperature in the ice compartment is around -1°
confirmed on the board that the thermistor is reading correctly around -7
when the test button is pressed sufficient water does go inside the ice maker with the door open or closed
there are no cooling issues that are present with the machine at this time
I was looking for help on checking what other issues may cause this I am suspecting the main control board
- Guest asked 5 years ago
- last active 5 years ago
My LG washer is noisy during use.
- Patrick's Appliance Service asked 7 years ago
- last active 7 years ago
The water valve for this refrigerator is leaking. The problem is that the valve LG is saying that it needs is a MJX41178908, the mounting is perfect but this valve is a single solenoid valve. The original vale is a dual solenoid valve but they give no instructions to convert. I wanted to see if you have run into something like this before, get advice, or see if there is any instructions on this. There is another valve MJX41869202. THe valve that is in there is way different than both. Amy advice or research would be greatly appreciated.
- mastertechca asked 4 years ago
- last active 4 years ago
I changed the infinite switch and it did the same thing.
If I begin on low it will heat and cut off but will not come back on even after 10 minutes. If I turn it off and then back on it repeats the same cycle. It will stay on high. If I set it on 3 or 4 it does the same.
Can this be the sensor in the burner?
How does it work?
It doesn’t matter if I use the single or dual settings.
- Guest asked 4 years ago
- last active 4 years ago
So I’ve replaced the tub bearing and tranny due to a leak, reassembled and tests good, washer 7 loads and it through a main computer replace error. Replaced the main control and door lock and it washed 7 loads and it wont wash again. The on, wash and lid lock light are on and it wont do anything. Any ideas?
- Guest asked 7 years ago
- last active 7 years ago
i have a cabrio washer that locks unlocks repeatly changed board and lock switch still doing samething
- Guest asked 7 years ago
- last active 7 years ago
I performed the callibration test as listed in the video and I got two error codes ,F-7, E-5.
could you please tell me what they mean?
- terry parrish asked 10 years ago
- last active 10 years ago
The machine washing very good…but in the finally cycle the door dont open..it is block…i cup the electric but nothing…i put the button unlocket for 3 ,5 ,10 sec..but nothing…i put out the filter of the pump i clean it but the door dont open is locket with the dress side…a thing is not normal went she come start washing she made a sound in the panel control..just click..click..click…excuse my inglish is not good….
- Ana Garcia asked 10 years ago
- last active 10 years ago
I can’t get my washer to spin and I keep hearing a clicking sound. I’ve turned it on its side and took off the shield, the belt and motor turn freely by hand. After watching one of your videos, I’m thinking I need the shift actuator part # W10006355 but wanted to see what you think before I purchased it. The washer appears to have a small leak, the actuator looks a little rusty.
- Lee asked 10 years ago
- last active 10 years ago
I have disassembled and repaired this in door ice and water dispenser 3 times for various fixes, but this one i need some help. Both ice and water levers fail to activate. i have replaced the plastic bracket in the past and it is not a mechanical contact issue with the levers. i have also checked the door switch with an ohm meter and it seems to be functioning also. what is the next part to look into? thanks
- chadp asked 10 years ago
- last active 10 years ago
Fridge freezes behind the back panel until the fan at first makes noise (hitting the ice) then stops and the fridge starts to get warm. When I remove the back panel I can see the ice is everywhere and there is a big lump of Ice around a wire or tube on the right, then at the bottom of the evaporator (I think that’s what you call it) so the drain at the bottom is all iced over. I have gone thru this process of taking it apart and defrosting it, each time within a few weeks we are back to square one. I saw a video of one of your guys fixing an issue in a very similar model in a video on your site called “Refrigerator Repair – Not cooling properly, freezing up on the back panel -Samsung – RF266AEPN” I Looks exactly like my issue, I just need to know the exact parts I need to do the job. Can you help.
- patrick goldstone asked 10 years ago
- last active 10 years ago
I think I have a hose leaking on top, but I can’t raise it up.
- Frank asked 10 years ago
- last active 10 years ago
everytime i try to wash my clothes it’ll spin once and 3 mins later it will say R-09. please help
- jesse asked 10 years ago
- last active 9 years ago
Fridgidaire (electrolux) affinity.
Error E66
Hi there and thanks for making the youtube video. I have the dryer open and the drum out. I have a multimeter but to be honest it is one of those tools I don’t really know how to use. What setting do I put it on to test the doohickeys? What am I looking for on the multimeter to determine if its bad or good?
After writing the first question on the youtube comment section I set it it the 20ohms and get a reading of 1.1 and 1.4.
Also when I took the dryer apart there was a lot of lint, coins and some other misc debris in the bottom of the dryer. Is this normal or might I have a leak somewhere?
- stephen asked 9 years ago
- last active 9 years ago
I’ve got this thing apart and have been checking parts to find the problem. It was tripping the breaker consistently and now I’m not sure what’s causing it. Checked the board, seemed fine. Checked the igniter, also good. Getting proper power to and from unit and the wall, so can anyone help me out?
- harold l asked 9 years ago
- last active 9 years ago
