Are your technicians wearing masks with the COVID-19 corona virus ? Is the corona virus preventing customers from letting technicians into their homes for repairs.
- Patrick's Appliance Service asked 6 years ago
- last active 6 years ago
The ice maker in my Samsung refrigerator is not working or working slowly.
- Don Kopecky asked 6 years ago
- last active 6 years ago
There is a lot of ice build up on the back wall of my freezer. What type of issue would cause this. Also ive been seeing “4E” pop up on the screen.
- Hall Refrigeration asked 6 years ago
- last active 6 years ago
My Samsung refrigerator is not cooling properly. 6E error code.
- David Sutton asked 6 years ago
- last active 6 years ago
I am getting an error code on my refrigerator and i do not know what it means.
- Don Kopecky asked 6 years ago
- last active 6 years ago
Both the fresh food and the freezer temp. sensors are reading low (-10 to -13 )each . The main board had been sent out last year for reconditioning , appearantly it’s long longer available. can we calibrate the sensors??
- Guest asked 6 years ago
- last active 6 years ago
Buttons are not working. Also getting C-40 error.
- T&G Appliance Repair asked 6 years ago
- last active 6 years ago
The door on my Samsung oven will not open up.
- Patrick's Appliance Service asked 6 years ago
- last active 6 years ago
- Guest asked 6 years ago
- last active 6 years ago
Does the Control Electronic W11164576 , have something to do with unit not making ice?
- Guest asked 6 years ago
- last active 6 years ago
Hello,
For starters not a fan of Samsung products,
We have changed the water valves and pressure switch.Checked the pressure switch hose for cuts all checks okay.
Unit fills with water drains it out then trows 4e error code ?
Any help Thanks
- Guest asked 6 years ago
- last active 6 years ago
UPRIGHT BUILT IN FREEZER, THE CONTROL PANEL WENT BAD ON IT. THE FREEZER STILL HAS POWER.
NO DISPLAY AND NO COOLING
- Guest asked 6 years ago
- last active 6 years ago
very noisy on spin , need tare down vidio to replace bearings and seal .
- Guest asked 6 years ago
- last active 6 years ago
There is an inch of ice in the floor of the ice room. Is there a service bulletin on this issues?
I suppose the customer has to let it thaw out.
Is this a problem with the water valve? The FILTER has been changed and water pressure is good. The icemaker was replaced 8 months ago.
Any information about this would be helpful.
- Guest asked 6 years ago
- last active 6 years ago
How do you take the unit apart to get inside to test the components?
- mramp asked 6 years ago
- last active 6 years ago
I need a service manual. I have water to the back where the line goes into the filter (I suppose it’s to the filter)The Ice maker fills ok but there is not water to the dispenser. When I push the paddle I can hear the valve actuate but, Nothing. Is there a secondary valve some where? I couldn’t find it in the door . If so where is it?
- Guest asked 6 years ago
- last active 6 years ago
The clothes are coming out wet. At times it is not spinning at all.
- Guest asked 6 years ago
- last active 6 years ago
I have a d5 error on my washer and i do not know what it means.
- Harley Clark asked 6 years ago
- last active 6 years ago
I have changed the water valve and it still freezes up. I have ran the diagnostics and the ice room temperature sensor is good, showing 3 degrees. The icemaker test is good. When I de ice the fill tube it will work and make ice for less than a day then refreeze.
It has done this 3 times.
The first time I found it froze and tried to run the diagnostics it would not work until I unplugged it and restarted it then it was ok.
What is causing this problem. The FILTER is good and so is the water pressure.
Is there a service bulletin on this or some other issue?
Or what?
- Guest asked 6 years ago
- last active 6 years ago
My washer just stops and displays a dL error on the screen.
- T&G Appliance Repair asked 6 years ago
- last active 6 years ago
My washer will not start. Also getting nF error code.
- David Sutton asked 6 years ago
- last active 6 years ago
My Samsung washer is displaying a error code but i do not know what it means.
- Harley Clark asked 6 years ago
- last active 6 years ago
This range will sometimes turn on fine and cook with no issues for a good little bit, but it will randomly just stop cooking with an error of E0 54 or E1 18. Sometimes the unit will try to startup but will go back to the same error codes listed above and not even start.
- Guest asked 6 years ago
- last active 6 years ago
