Repair Help

Customer complained of icemaker not working. Valve checked out ok, replaced icemaker and after 24 hours still no ice and doesn’t seem to be getting power. GE Monogram series. Any ideas? Thanks.

Need technical information on compressor run

I replaced the light under the microwave but it won’t work.

We are not getting any water into the dishwasher. Water lines are hooked up

Can hear fan slowing down and speeds back up, at the same time I can feel the air flow with speed of fan.

My microwave keeps giving error codes and i dont know what they are.

Clothes still coming out wet.

Maytag gas dryer LDG7500AW. Gas flow shut off mid-load and will not turn on despite trying various settings on controls.Igniter glows red but shuts off after 15 sec or so without any flame appearing.

I have an LMXS30776S/00 LG refrigerator with no cooling whatsoever. Refrigerator has never been used. No heat felt on compressor. Resistance across C & P terminals of compressor is 8.2 ohms. All sensors in freezer and refrigerator check out good. Smart diagnosis comes up with no data. When i test PCB, I get a 3 blink code on LED. Tapped high and low side and pressure remains the same with and without power. Is my compressor bad or PCB? Voltage gets up to 13V0AC before it times out.

The dryer will not spin it sounds like the motor is engaging but not spinning the belt is fine I do not know how to diagnose the problem.

This LG dryer has correct voltage coming into it. No visible signs of arching on the user interface or the control board. None of the buttons do anything on the user interface. No lights on at all besides the door light when you open the door. I wasn’t sure if I should try replacing the user interface or the control board. Or what can be tested to verify one or the other.

The thermister checks normal. This dryer has no display to read the error code’s. I need a service manual. Whatdoes this sound like?

We need a tech sheet and service manual

The valve that lets cold air from the freezer into the refrigerator chatters open and shut constantly.

Need a service manual on this smart all-in-one washer & dryer combination unit.

I’m guessing DSI or oven spark model.

need to hold start switch on to operate dryer changed switch it operted and now not operating after 2 switch installed you need to hold it on with hand to operate

Standard S/S unit, that on the freezer side will ice up around the ice maker and the ice bucket. (Looks like the snow cone ice when a defrost heater goes bad just around the icemaker area). I have replaced the door seal, the ice door flap and part with it. I am at a loss hear, as h/o swears door is not being left open. Only thing I know it this point is maybe the door insulation is bad and needs another door? Any ideas?

Hello, I have an error code E207 for my Bosch oven. The latch does stick. How do I clear the error code?.

I put new belts on my washer. it was tilted back so when i turned it on it went to wobbling and then cut off. since then i put it back down on the floor to let the water level out and it will not start.

Whirlpool Range WFG361LVQ3. The display shows ‘cool’ . I have unplugged the power. I have tried to look for a fault code. All to no avail. What can I try next?

Our microwave is not heating food. It turns on and light up and the time starts, but then no air or heat comes out
Its an LG model number LMH2016ST.

freezer not cold enough for ice cream intermittently making ice cubes refridgerator working ok

History:
Unit slowly stopped make temp in both frig and freezer over the course of a week. Diagnostic screen showed that the Frig defrost sensor was bad. I replaced the sensor and cleared the fault. Only seemed to make matters worse. Freezer eventually rose to ambient and frig would not make it below 59deg F. Compressor and Comp fan were running but at what seemed to be a considerable lower level then typical. You can’t tell the comp is running unless you get behind the unit and down by the comp bay. When new, the unit was quite noisy and there was no mistaking when the unit was on high. I used the manual diagnostics to force the compressor to hi-F1/med-F2/low-F3. The output does change, but someone needs to have a hand on the compressor to tell the difference. I tested the windings on the motor and none were shorted, so I replaced the inventor board even though the diagnostic LED was solid. No change. The comp signal coming off the main control board was only at 2.0vdc, so I changed the MCB. No change. Current comp signal on new MCB is 2.1vdc. I would like to test the out of the invertor but don’t have a service information on the output voltage. I was ready to think the compressor must be bad but I looked at the unit status indicators and got some very confusing data. First both the >92deg (Overload) and <72deg ambient condition are both active. I am not sure how this happens unless the sensor is bad and even then it should fail high or low. Next it shows the compressor as “Off” when it is running. It also shows both defrost heaters as active when the unit temp is at ambient. I have a picture of the status display if you provide an email to send or place to post. Thank.

I just replaced the heater unit due to an Error Code 73. I am now getting an Error Code 91 some kind of communication issue.

Is there a cause for this issue? Any service bulletin or repair kit? Or do i need to replace the evaporator cover assembly? Can a sealed system failure cause this?

Water slowly leaks into the dishwasher when it is off. So the bottom of the dishwasher has a pool of water if not in use. There was sediment in the water valve, so I replaced the water valve… but the dishwasher is still leaking slowly while off. What could cause this issue?

Drains, fills,door locks, but timer keeps resetting ( adding more time to the cycles) when there is like around 9 mins left in cycle. Clothes are still wet. But it spins. Can’t get it to diagnostic mode to read any error