this dryer has a softener like a bleach disp. on the washer on the left side. what is the best way to remove the front to remove the tub.
thanks
- Guest asked 9 years ago
- last active 9 years ago
This unit had an error code “PF” and a technician replaced the control board, after a couple of days the washer just died, no power whatsoever. Wondering if anybody has at suggestions.
- Guest asked 9 years ago
- last active 9 years ago
I know AC systems have temperature sensor on the condenser coils to know when to kick on the condenser fan but do refrigerators have this as well? I replaced the condenser motor and it still won’t come on and the compressor is nearing 200°F . I just shorted the wiring to eliminate the switch from the relay and now it will always be running. Better to kill the new condenser motor then the compressor or relay right? Two questions:
How long could a condenser fan run before dying nonstop?
What could be causing this ? The relay or wiring possibly? Motor is getting proper voltage but the switch is not receiving the five bolts for the activation so I bypassed the motor 13.5v line over to the switch and disconnected the switch so it doesn’t run the voltage back to the relay and fry the relay.
- Guest asked 9 years ago
- last active 9 years ago
The dryer takes 3 hours to dry a load. I checked the vent lines, filter, replaced the heating element along with its thermostat.
I looked at the parts diagram. And what is the purpose of the Control Board,temperature,ATC ?
Should I replace any of the thermostats?
I put my temp meter on the inside wall of the dryer vent as it ran. its temperature went from 111* to 138* on time dry and It slightly rose and fell in a time of 5 minutes On more dry setting it red 128* to 148* slightly rising and falling in a 5 minute time.
Should the temperature stay or maintain a setting of ( let’s say ) 145* for a time of 5 minutes? And then gradually drop and stay at 120* for a couple of minutes?
This dryer is giving me heart burn.?
- Guest asked 9 years ago
- last active 9 years ago
Ice filter not changed in two years and existing small amount of cubes are small.
What is the method to cycle ice maker and perform test:
I will assume I have to fix a defrost thermostat/thermistor assembly. I need to be able to test and disassemble freezer back panel and ice maker Dissasembly.
- Guest asked 9 years ago
- last active 9 years ago
The dryer belt on the Samsung dryer comes off about every 2 or 3 months. I checked the pulleys including motor pulley and belt tension pulley and I see no problem with them. The drum rollers look good and are not worn and the inner drum seems to be fine. I asked the customer if they were turning the drum counterclockwise when they take the clothes out. They said no. I also asked if they were overloading the dryer. They said no. THe dryer is 2 to 3 years old. Any suggestions? Thanks, Ray
- Guest asked 9 years ago
- last active 9 years ago
Can you please provide a wiring diagram for this model?
- Guest asked 9 years ago
- last active 9 years ago
ARRIVED AT HOUSE FOUND ICE BUILDUP AROUND EVAPORATOR ICEMAKER FAN. DEFROSTED ICE AROUND
FAN BLADE. CUSTOMER CALLED COMPLAINED SLOW ICE.
- Guest asked 9 years ago
- last active 9 years ago
This dryer became hot and burned up the thermostat completely and some burn marks on the metal inside the machine. I replaced both thermostats, the heating element was grounded so I replaced it also. After reassembling unit and running a few minutes a HE error code came on. We had the vent cleaned and I replaced the thermistor. Unit was used for 2 days and the HE error code has returned.
Any ideas of what to do now?
Thomas Butler
Cell 210 209 3029
- Guest asked 9 years ago
- last active 9 years ago
Dryer still not drying properly. After replacing the heat element.
- Guest asked 9 years ago
- last active 9 years ago
- Guest asked 9 years ago
- last active 9 years ago
do you have a video on this lg dryer. how to get into
- Guest asked 9 years ago
- last active 9 years ago
Hello, I have a dryer the is showing an e71 error code. all the sensors are checking out good the only thind is one of the 3 coils is bad would that cause an e71 code?
- Guest asked 9 years ago
- last active 9 years ago
what should I test or part I should try
- Guest asked 9 years ago
- last active 9 years ago
drain pump kicks on and all the water is pumped out and of course the machine stops and doesn’t finish the ice
- Guest asked 9 years ago
- last active 9 years ago
Hi
I have a 6 years old whirlpool dryer that does a really strange rattling noise
i replaced the pulley the belt the rollers (the axles are in good shape
i even replaced the motor
It still does the same thing
Any ideas what should i do ?
- Guest asked 9 years ago
- last active 9 years ago
fridge is not keeping things cold…the freezer is not keeping items frozen…tempurate setting up high for cooling but not working….when trying to turn the tempurature down, goes back to where was before. Kenmore Elite Fridge.
- Guest asked 9 years ago
- last active 9 years ago
I am going out tomorrow to check this problem if you have any suggestions please advise
- Guest asked 9 years ago
- last active 9 years ago
cust. has code problem fleshes either HF or FH cust. cannot tell
- Guest asked 9 years ago
- last active 9 years ago
I want to know how to test the components for this problem.
- Guest asked 9 years ago
- last active 9 years ago
There anyway I can get a link how to change my whirlpool front loader washer or a video
- Guest asked 9 years ago
- last active 9 years ago
everything is working fine..
the compressor and the fan are working.
however the fan in the freezer is just not getting power…..
the fan works when I put it in to 110 not the unit is not supplying power to the fan
- Guest asked 9 years ago
- last active 9 years ago
The heat guard fell off the back of the drum. I checked the continuity on the dryer element and got continuity. I reattached the heat guard and put it all back together. Not the dryer gets warm, but does not dry the clothes. My assistant said that the heating coil doesn’t get red hot. Only a slight pink / red color.
- Guest asked 9 years ago
- last active 9 years ago
no water or ice disp and light
- Guest asked 9 years ago
- last active 9 years ago
I went to the service call and the complaint was the door look contiuosly blinks
I changed the door look and all seemed fine so i set the water level to smallest load the machine started to fill and nearly filled up the tb so I pushed the stop button and set it to spin drain after that now the drain pump comes on and no led lights on
- Guest asked 9 years ago
- last active 9 years ago
The refrigerator was not running. I look at the main board and observed the green light on the board blinking 6 times continuously after 3 seconds it blinks 6 times continuously. is it an error code or what. The tech sheet said nothing about the blinking light on the main board.
- Guest asked 9 years ago
- last active 9 years ago
On this washer i have the UE error code which is the unbalanced code or that the basket won’t spin over 150 rpm. So I have reset the system and installed new shocks on the washer. Can you please help me out?
- Guest asked 9 years ago
- last active 9 years ago
My customer has a GE Profile JVM2070SH001 Microwave and reports that the lights on the touch pad light up when the door is opened but non of the buttons will work when trying to start the microwave cooking cycle. any ideas will be appreciated.
- Keith Nelson asked 9 years ago
- last active 9 years ago
WHAT COULD BE CAUSING THE OVEN TO NOT GET POWER TO THE BAKE ELEMENT IN THIS UNIT.
- Guest asked 9 years ago
- last active 9 years ago
How to test the ice maker voltages output?
- Guest asked 9 years ago
- last active 9 years ago
