Repair Help

GE refrigerator #PSB42LSRBBV Serial #LG070289 Freezer drain keeps iceing up every two months

Hello
We have a freezer drain that keeps plugging up every 45-60 days. We have thoroughly made sure it is defrosted with no deposits in the drain. Does anyone know if there is a recall on this issues or service bulletin ?

I got this frididaire top and bottom older fridge anyway i dont have model number but heres the simmple question. I checked the amperage on it it is drwing 1.25 amps every thing running, but still warm on both compartments? REMEMBER EVERYTHING RUNNING< FANS GOING DEFROST TIMER WORKING< LITES ON SO WHAT COULD BE THE PROBLEM?

I opened the freezer door and water ran out. There was a 1/4 inch of ice in the bottom and thicker is you looked back. Ice was down the back under the evaporator. No signs of an iced up evap coil. After I cleaned all the ice out I was wondering where the drain hole was?? I pulled the bottom tray from the cooler side, no drain?? The coils underneath was dirty. All fans were running ***Note the ice maker water is turned off under the house…..

the oven will not work .
the screen is blank
the burners do not light with the electric
only by match

the oven will not work .
the screen is blank
the burners do not light with the electric
only by match

The gas duet dryer only lights up for touch up mode and 15 minutes. When I turn knob for different settings touch up still stays lit. Automatic controls will not work no matter were control knob is turned. I can adjust settings on right side including time and heat but everything else does nothing. The original complaint was a F01 code.

THE PADDLE TO GET ICE AND WATER WORKS BUT NOW YOU HAVE TO PUSH EXTREMELY HARD DIDNT HAVE TO IN THE BEGINNING

oven wont work I reset house breaker it works when I try again I get error code feature not aavailable theni need to reset breaker and repeat steps

I have a GE SPACEMAKER stackable washer/dryer. Customer complained that the washer knob broke off and that the washer is not working. When I arrived I noticed the knob from the washer side was off the potentiometer aperture handle (timer knob) resting on the washer. I tested the dryer and the dryer appeared to be working fine. I tried to start the washer to test it by turning the timer knob (which had fell off of the control panel frame bracket) and pressing start button. Not only did the washer not show any sign of life by not starting, but I tried turning the knob on the timer without the knob attached and I could not hear any “click” coming from inside the timer indicating that it was advancing to the next stage of the washing cycle.
I removed the control panel cover and noticed the timer slid out of place in its socket when it was supposed to be securely fastened to the front panel. The knob was turning but the timer was not clicking as it advanced. I tried to unplug the connector OF THE TIMER from the wires but coud not notice any discrepencies visually. Should the wires have been checked ?? continuity ? voltage ? Could I have a bad timer ? If the dryer works fine and the power is getting to the dryer and stopping when it gets to the washer could the timer be preventing this ?
Timer part # 131758600 (WRITTEN ON TIMER ITSELF)
GE Spacemaker Washer Dryer combo WSM2700DAWWW

The only thing that works in the fridge is the light. Nothing else comes on.

I have an lg dryer that when plugged in keeps running with the display off. I can unplug the user interface and it keeps running the dryer is unplugged.

Had a guy ask me to checkout a fridge. He said it wouldn’t start. I checked the compressor and there was nothing plugged into the compressor. I ohm-ed it and got 10, 7 and 4 and none to ground. I put a 3n1 on it and plugged it in and it ran like a charm pulling 2.8 amps. Max load said 6 amps. So what do I need to put original parts in this unit. I think I have found the 3 parts but want to make sure they are right. Thank you!!

Not cooling, evaporator fan not moving. There is power to it. Its like it’s in magnetic field. Try spinning it won’t start up.

Trying to figure out how to change infinite switch. I have to remove glass from control panel to get to screws and unable to figure out. Steve

i was wonder if anyone can tell me how to replace the door seal on this unit
item #137066300

Researching this and wondering if service bulletin out there for this issue. Customer states doesn’t matter what size load. All I found is impeller issue but would like confirmation. Thank you, Steve

Ice shoot this refrigerator has sensors on each side. The led is flashing when you have freezer door open. How to you test the ice maker? When you block the sensors both sides the led still flashes red. Is there a way to test ice maker with the door open?

Tech Sheet is missing from the appliance, can you provide an error code list for the machine. thank you

Washer won’t spin. How do you know computer is bad? Or the interface board? or the other interface board? There are two boards that communicate with the main computer board.

so the customer said that the machine will not turn on.
when i got there i open the controls and saw a red light flashing tried to turn it on and it went.
i did see the igniter ignite and all was fine.
the customer called me back to say that it dose turn on but will not heat

so im getting a E51 error and the customer state that the dryer keeps on running