Repair Help

hi so we have 2 issues with the stove top.
1. the two middle burners will not light by itself i hear the clicking but it sparks at the rear right not the middle where i want to light it.
2. the left and right front burners have a real small flame.. there is very very little gas flowing to the burner hence the small flame

CUSTOMER LOADS WASHER , WILL FILL WITH WATER , WILL SENSE LOAD AND START WASH CYCLE, WILL START ADJATAING FOR ABOUT 8 MINS DRAIN AND STOP ,DOOR WILL UNLOCK , AND WITH ERROR CODE, DISPLAY WILL SHOW WASH AND THE AMOUNT OF TIME LEFT IN CYCLE. THANKS

Brand:kenmore
model: 110.85091401
dryer it wont responde to any control,
it wont start.
is there any video on this brand?

Won’t bake or broil need wiring schematic

I need someone to clear me up on some functions on most dryers please.

1 Thermal fuse… Blows if the???
2 Over heat Switch. Just as stated. Blows if air flow is obscure temp spike.
3 The Temperature control. The 4 prong switch that monitors temprature. 2 prongs for sensor and 2 prongs for control?
4 The switch at the element that has 2 prongs 1 to complete circuit another prong for? Then L2 straight in to the element….. Thanks….

Those Samsung dual cool types are nasty to solve or work on.
First off I unplugged it for 15 minutes to reset. I went to put a cooler eval fan motor on it..
Codes cooler side readout 88 is what it looks like the code is the bars that make up the 8… Freezer side has no faults
First 8 right side both vertical bars lit.
Second 8 right bottom vertical bar very top and very bottom horizontal bars lit..
Any thoughts?

I have a customer with a washer that will not stop beeping. The first time out I found a restricted fill line that would not let the unit fill and wash. Corrected that issue and units runs. Bosch will not talk to me as I am no longer an authorized anything. The customer and I have both determined that the controls work to the point you can raise the tone level and lower it to off. I did change the main brain, on advise from another servicer that said they solved a similar issue by changing the brain. Unit seemed to work okay, left the house and came home. As I walked in the door the customer called and advised the unit ran part of the way thru and started beeping. At last count she had it at 137. Has anyone any suggestions that will help me help her. Thanks.

We have a SXS refrigerator, customer complaint it’s frosting around inner door frame.
This customer has had 2 other companies out also. First company out, leveled unit ad adjusted doors.
2nd company out found no problem at all.
We were dispatched the call by Frigidaire. We went out the customer had cleaned everything up, so no evidence of a problem. We checked everything that could cause problem, nothing apparent. we advised the customer if it happens again. Leave it, don’t clean it so we can see it etc.
She called us out again in about 2 weeks (you have to love warranties like this) she had small frozen water spots on the lower freezer door shelves about the size of a half dollar. Similar to if the ice bucket was dripping although their is no evidence that it is.
1) ice door not leaking air and is closing in under 8 seconds.
2) no air leaks around gasket at all. Passes dollar bill test.
3) no air leaks around fill spout at icemaker
This one is a real head scratcher as it’s an absentee owner and anyone that is there is 0 help.
Tech line is NO help at all.
Has anyone else run into anything similar issue ?
Thanks in advance.

You can start the dryer again it will just shut off completely. What do you think this could be?

This is a replacement kit found on many samsung washers there are no videos explaining how to do this. Please add a video thank you

This stove had the bake element go out. The element was replaced. It still didn’t work. It was dropped off. After checking the OHM’s and then voltage. It OHMed out okay. The 120 VAC was right on. It does feed direct. When the oven is turned on it does nothing, bake or broil. Voltage from the board is none… I removed the board and the roach “stuff” was bad. I don’t see any shortages or burnt spots on the board but it is apparent there is no output from the board. So, I’m leaning to the board.. Are roaches a major cause of failures to these type of appliances?

replaced left hing part#wpw10299224 now the door at lowest position comes up hard too fast

What controls the flow of water into the GE ice maker. The water dispenser works fine,

Ice forms in the drain then leaks under bin I have defrosted and cleaned drain installed short wire into drain to keep it warm during defrost, it still comes back after four months. Is there fix for this problem Samsung made this for GE

Water leaking from bottom of front loader. How do I open up the machine for inspection of pump? What do you think this could be a bearing problem or just a water pump or hose?

I purchased Appliance Video for help on this unit. You have no videos or show this unit exists. Type in the Model # and nothing. This unit is not cooling in the refrigerator section. The freezer side seems fine. I cannot hear the evaporator fan run. leaning towards the fan in the cooler side??? Will go to it tomorrow. Help if you can!! Thanks!!

What would cause this Oasis to shake violently during the spin cycle? It shakes so much, that it hits the sides of the outer casing. And the board reads Ul.

I HAVE A CUSTOMER THAT HAS A COMMERCIAL MILNOR WASHER. THE UNIT WILL GO THROUGH CYCLES UNTIL IT REACHES 19 MIN. IT THEN STAYS IN THE WASH CYCLE AT 19 UNTIL IT SHOWS A CODE FOR A BAD PRESURE SWITCH. I CHANGED THE PRESURE SWITCH AND CALIBRATED IT. WHEN I LEFT IT, THE UNIT WAS DOWN TO 15 MIN. I WILL CALL TO FIND OUT WHAT IT DID. IT SEEMED TO ME THAT THE CYCLES WERE TAKING TO LONG, AND NEVER DRAINING WATER EVEN THOUGH IT SAID THE UNIT WAS IN THE DRAIN CYCLE. ANY GUIDANCE OR HELP WOULD BE GREAT, THANKS, TODD FROM NY.

this is a matag 2 door bottom freezer fridge. the hose feeding the water filter from the inlet needs replacing. I can’t get the housing off. there is a screw in the side that I removed, but something in the front right bottom corner of the housing is holding it on. also I pushed in on the water filter and now its locked in there and doesn’t want to come out. there is some give when I press in on it but it won’t come out.thanks.

customer states that the machine will spin but will not drain the water

Parker &Fisher, not spinning motor getting hot? Is there a way to know transmission is bad? How do you put this machine in diagnostic mode?

All fuses show 120 in and 120 out. Problem is I only have 25 volts to ignitor when turned on. Dryer does not have timer diagnosis legend paperwork. Any suggestions?

hiow to access door lock assyembly and how to trouble shoot and prove assy needs replacing

Can you find a video for replacing the main control board on the Whirlpool Washer WFW8640BW?