Repair Help

So I changed the coils and the igniter and the senser.
The falme still will go on for 5 to ten seconds and then go off.
And will repeat about 1 minute later
I have have taken the vent off of the back and no difference

The customer States that after a self clean on the oven the thermostat light indicating what selection is chosen does not work I have tried to put it on bake or broil even self clean and nothing happens there is a light in the oven itself that does work and the top burners are working as well

Ice forming around ice maker looking at this model GI7FVCXWY62 not sure why there is Ice forming. This Refrigerator is real problem. You say there is a facial heater for the unit. They say there is only a mold heater, when I talked to Whirlpool. They also said they are not having any issues with the unit. There are problems and I don’t know what is real causing the iceing problem. Does the unit have factory problem thats causing this iceing problem. Please let me know I so confused about the whole thing. I just don’t understand why they ever put the ice maker in the upper left side of the refrigerator. I really think it is a bad design. The plastic that you have to pull down is so brittle and you can break a part so easy. All the cold tempatures for years and years of operation. Please let me know if this model of refrigerator does have a fix for ice problem.

Thank You
Dale

How do you test the control board on this refridgerator and how to make it defrost?

Hi.
Hi the dryer was making a screeching sound when there was a load inside I took out the drum and greased up the bearings I replaced everything back and now I hear a light switch and sound even when it is empty and we’ll progress when it’s full

The customer hasn’t used their ice maker in the ice room (fresh food section) in a couple years because it stopped making ice. Today I was there, all around the ice maker mold and motor it was covered in heavy frost. I got that out of the way. There were cubes on the “fingers” of the evaporator. I have never worked on this type of ice maker before and need some guidance on how to trouble shoot it
The mold was below the fingers (not sure what they’re called).
Can this ice maker be forced cycled?
Do you have a video on how to take it out and inspect it?
I understand there’s a fan motor in behind it, I did not hear it running.
Any help would be greatly appreciated.
Thanks,

This is a duel fuel range. Its got gas burners on top, with a glass cooktop. I just found out that the top doesn’t come off. Does anyone know how to install the switches to the burners ??

How do you know what valve is causing a water problem? Water is all inside where the ice maker is at. There is a primary valve which they call a smart valve. Then there’s a secoundary valve.

Whirlpool Refrigerator French door bottom freezer. The unit is all iced up where the Ice maker is? How to you take the Ice maker out? It has all snap parts with screws to come out.

The dryer makes a loud metal in metal sound when it it runs.
Did notice it dose lighten up when there is a lot in the dryer

Lg washer how do you reinstall spring and locker hook and pin on inner door panel? I cannot figure how to put the spring back on.

GE PROFILE WASHER IS NOT STARTING, SHUTS DOWN AT START OF CYCLE.

Do you have a video on replacing the damper assembly on this unit?

Center burner one element like grittle. What is happening two separate infinity switches. If you turn on either one of the burner it will blow the 40 amp breaker.

the customer says that there is water leaking from the bottom of the machine.
he also said that when he turns off the hot water there is NO leak but when he turns it back on the machine leaked over time.
i have open the bottom of the machine and checked the connection it is dry.
however there is signs of water on the floor

Hi Folks,
This unit contains a W10135090 Board which is replaced by a part number 2252189 but this replacement board is hard to come by. They just don’t have them in stock! Why I don’t know! The Repair Shack made a repair on the W10135090 and said it was good to go…Installed and still not cooling. But in the fresh food compartment controls if you install a bulb in to the top of socket near the Led the Led goes off. If you loosen the bulb the LED showing the temperature setting goes back on! Anyone have any ideas on this situation. All input greatly appreciated.

Replaced the evaporator fan and main control board and the fan still isn’t coming on.

Customer calls and states this fridge freezer side is cool but fridge side is warm.

We have this cooktop and it is giving a f122.Anyone know what this could be?

what is involved in replacing door handles with customized panels

We have had for of these washers that have gone bad where the bearing in spin sounds like a jet airplane taking off. each time, we have found the tub support stuck to the transmission shaft, and no matter what, we can not get it off. has anyone had any success removing the spin basket?
If you have let us know how please.

Good afternoon I have a GE washer that does a self diagnostic when first plugged in. The error happens when it gets to the check drive system part. The customer said it made a loud clunk and then wouldn’t drain the water. I ran 120 to the pump and it discharged the water but every time it tries to spin it sounds weird and flags a very general error the “a problem has been detected with this unit”. Any help would be great.
Thanks

My customer had an electrician look at her dryer. I’m guessing that he did a continuity test. And removed the “part” that sits on the side of the exhaust line. And he never came back to fix it. Well, that’s the story that I was told.
There are two wires and a little hole in the can that is about half way in back of the exhaust line. I checked out several websites, and I didn’t find a hole or a part that goes in the middle of the exhaust line. One person said that it is the drum outlet bias thermostat. But it looks like it’s located at the front of the dryer.
If you can shed any light on the subject I would greatly appreciate it. If I order that $64.00 part and it’s not the right part. Besides being stupid, I’d look stupid.
Thanks?

I have samsung diswasher shows heavy code. the diswasher continued to run, the drain pum keept running only way to turn the unit off is by turning the breaker off. any segestion

Please can you tell me where the water valve is located on this refrigerator. water and ice not working. please attach video if there is one. thank for your help

Microwave blow 1 of 20 amp fuses. Replace it and test circuits before plugging in. Disconnected the mag tube and tested diode gate. Turn power on display came on set the clock. Blower fans works on all speeds. When you set the cook time it the start swich blows the same 20 amp fuse. Looks like a bad short circuit. What do you think the problem can be. I tried everything?

I have a dish drawer that overfills.