0 votes
4k views

I will be looking at a Samsung refrigerator with above model number (from customer). Says water is not dispensing, was a sporadic problem before but now nothing. It does dispense ice cubes.
Where would I find the tech sheet on the unit?
Does anyone have the tech sheet to send? Thanks in advance

0 votes
3k views

I have a LG refrigerator , the defrost drain is not draining. Completely cleared it out 3 days ago, but water does not drain. Heater works fine, thermostat is good, but it looks like the drain is not lined up? Is their a recall on this unit?

0 votes
3k views

I found the leak on this dishwasher coming from the diverter motor. I have changed one of these in the past and it continued to leak. Is there a repair kit ?

0 votes
4k views

No error codes or flashing lights. water seems to get hot.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

I checked out this dishwasher for not disolving the Finish detergent tablets. The first fill had plenty of water and all spray arms turning, second fill same thing, on the third fill I noticed the DW did not sound the same. I opened the door and the circulation pump was running but there was no water in the unit. My initial thought is bad water inlet valve that got hot and stopped working. Could this be a bad control board not sending power to the valve? Doesn’t sound logical since it worked initially. Any ideas on how to check this one.I’m going back to it on Friday morning. Any help is appreciated

0 votes
6k views

Samsung refrigerator dispenser controls not working, all buttons not working. Display has the 3rd led from bottom in freezer section lit. Is it the errror code for bad freezer defrost sensor? Tried to check ohm reading for sensor at pcb, had open circuit. Wire colors did not match tech sheet. CN40-6 was blue not blue/grey.
I have very little experience with Samsung, but does this look like the defrost sensor needs to be replaced? I don’t see any listing of a “defrost sensor” in the Sears parts listing. I see Refrigerator sensor, thermal fuse, fixer fuse, fixer sensor. Which one needs to be replaced?

0 votes
10k views

I have a Samsung washing machine error code NF1 any suggestions.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

the washing machine makes a sound when it washing clothes the sound seems like a squeak

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
35k views

Please advise of fault code 8E on a Samsung washer

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Having trouble stopping a noise in a Samsung top load washer have replaced tub and stator/hall sensor assy. Noise only occurs in powered spin, most notable as it starts spinning. No noise rotating drum or rotor by hand. Manually pulling shift lever and rotating rotor also no noise. Cable from actuator to shift lever seems slack, but no noticeable damage to splines. Any idea what this sound could be caused by? Thanks in advance

0 votes
3k views

Unit was originally a no cool call. I replaced the Interface and control board kit#5303918583. The unit would then not give any ice or water. I went back and took the connectors all off the interface board and reattached. Unit started making ice and giving water, however now when the unit fills the ice maker with water it also runs the water at the door. Anyone with a direction to point me in? Thanks in advance

0 votes
3k views

My Kenmore dishwasher is not coming on and is completely unresponsive .

0 votes
3k views

My gas GE oven is not baking.

0 votes
3k views

My GE refrigerator is not cooling properly. Any suggestions? I have frost on back wall …

0 votes
3k views

My Whirlpool refrigerator is not cooling at all in the fresh food or freezer section . Any suggestions?

0 votes
3k views

The lights on the control panel on my Jennair stove will not come on.

0 votes
3k views

There is ice building up in the back of my Hotpoint freezer.

0 votes
3k views

My LG electric dryer is not heating.

0 votes
4k views

Just wondering how to do a continuity check on a GE motor 5kh41jt18as has a yellow orange blue red black wires or if I were to make up power cord where would I hook it to and also where is the capacitor on this motor

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

So the dryer was making a rattling sound when it starts and ends.
I thought it was the belt or ideal arm so I changed them .
No luck the noise is Evan worse now and the drum has no force to it.
Meaning if I put in a wet load it will not turn.
2. After I put the dryer back I have a strong burning smell when we start the washer.
It filled with water but will not advance to anything else.
I hear the timer clicking but that’s all I Get.
It is a 25 year old machine.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
4k views

My customer called about her kitchen sink being clogged. And when the dishwasher drained it just added to the drainage problem.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

My GE refrigerator is not cooling and I don’t think I can hear the compressor running.

0 votes
3k views

My Electric Maytag dryer is not heating.

0 votes
3k views

My GE microwave will not shut off.

0 votes
3k views

My Whirlpool washer is leaking water from the door.

0 votes
3k views

My LG washer is leaking water.

0 votes
3k views

My Maytag refrigerator is not making ice.

0 votes
3k views

My Whirlpool dryer will not start. Any suggestions?

0 votes
3k views

My GE range will not bake.

0 votes
3k views

Complaint the machine works perfectly till the rinse cycle. when it spins out and goes to rinse the machine stops. i just printed out Manuel will go back an check for codes. Any body have this problem? or what should i be looking for. thank you in advance for any help in advance

Showing 6871 - 6900 of 9k results