Repair Help

Double oven will not work and keep getting F97. What is the likely problem? Lower cooling fan will not run. Found service bulletin that says to check connector. It’s a double oven so it will be very involved to take it down and really check it but as far as I can tell by peeking on it it looks ok. It says to replace cooling fan and sensor board if it’s ok. Is the cooling fan and sensor board more than likely bad based on you guy’s experience?
Thank you.

Hello this specific issue is on a Kenmore dryer 796.81172210. The cooling light stays on and there is no heat. I have replaced heater which solved the heat issue but my question is why is the cooling light staying on??

I have experienced this issue many times in Samsung dryer especially once it’s fixed the heaters on and the light stays on after repair Any thought to why this is?

Is there a self diagnostic mode. If so please explaine how to use it.

I have a Whirlpool French Door Bottom Mount Refrigerator. The icemaker has a slow drip out of the front of the icemaker heater cover. The water slowly drips down into the front ice bin. the Ice bin in the front door builds up with ice and eventually the water starts to run out of the opening of the front door and the water and Ice dispenser unit installed on the front door.

How do I stop the water from dripping out of the icemaker front cover?

The right door on this refrigerator pops open when the left door is closed first. I replaced the door cam, part #12028505ap but it did not stop this from happening. I have been telling my customers to open both doors and close the left door first in order to insure both are doors are sealed properly. I have not found an answer on the web. Hopefully your repairmen have found a solution.

Thank you!
Mel
My Appliance Repairman Inc.

My Samsung dishwasher is displaying a 4c error code.

i have customer who have Samsung induction range, and they got error E-84. keypad is not responding, i check the all control board and non of them have burning sign, i am planning to change touch pcb both side control board, i also download service manual and it says either invertor board or touch pcb board. how i can check inverter board without doing so much disassemble cook top remove. give me good plan to check

HAVE TRIED DIAGNOSTICS WHAT ELSE CAN I CHECK BESIDES DISPENSER AND LINKAGE

Frigidaire combo laundry system, model FFLE3911QW0 stopped and I retrieved error code EC6. The entry from the tech sheet is pasted below. How should I troubleshoot this, or what are the likely causes of this?

The interior light on fridge and freezer are flashing continuously. Front panel is showing upside down codes. Compressor is not starting. I changed door switch didn’t do nothing.
Can you please send me manual or put me in the right direction on what could be the problem?

I have a Samsung washing machine error code NF1 any suggestions.

I have a GE dishwasher and the Vent Cover keeps “Popping Off” and the is Vent Leaking . Is there a fix for this issue ?

I have a GE SPACEMAKER stackable washer/dryer. Customer complained that the washer knob broke off and that the washer is not working. When I arrived I noticed the knob from the washer side was off the potentiometer aperture handle (timer knob) resting on the washer. I tested the dryer and the dryer appeared to be working fine. I tried to start the washer to test it by turning the timer knob (which had fell off of the control panel frame bracket) and pressing start button. Not only did the washer not show any sign of life by not starting, but I tried turning the knob on the timer without the knob attached and I could not hear any “click” coming from inside the timer indicating that it was advancing to the next stage of the washing cycle.
I removed the control panel cover and noticed the timer slid out of place in its socket when it was supposed to be securely fastened to the front panel. The knob was turning but the timer was not clicking as it advanced. I tried to unplug the connector OF THE TIMER from the wires but coud not notice any discrepencies visually. Should the wires have been checked ?? continuity ? voltage ? Could I have a bad timer ? If the dryer works fine and the power is getting to the dryer and stopping when it gets to the washer could the timer be preventing this ?
Timer part # 131758600 (WRITTEN ON TIMER ITSELF)
GE Spacemaker Washer Dryer combo WSM2700DAWWW

My Electorlux range is getting an E31 error code.

hi. this unit is making noise when door is closed. there is ice building up on the evaporator.i seen the pictures on how to install the above insulation kit.but still confused,do the strips of insulation go underneath the drain pan and on the backside of the metal plate behind the evap coils. so that when the coils are back in place the strips cannot be seen.thanks

Kitchenaid built in oven microwave combo KEMS308SSS00. Original call was for a F1E5 error inverter. Inspection of inverter the board was clearly burned in several areas. Replaced inverter board and main control board.

When powered back on got F0E6 lost communication error. Checked all fuses and wires between Appliance Manager Board and microwave user interface. Had to replace manager board. After replacement, F1E5 error came back.

What have I overlooked or done incorrect? I would like to get this running for the family. Thank you.

Pump motor constantly running giving error code i30 checked drain pump everything working fine

Have a refrigerator with broken wires at bottom of freezer door. This is causing the ice maker not to run. Is a new wire harness available and any info on how to replace.

Customer called with a Samsung dw model DMT400RHS, lights flashing on SMART AUTO and HEAVY.
Does anyone know what this code means?

We have aproblem with this unit. it doesn’t make any ice . We found for sure the one of inlet valve coils is open ,
but the same time we can hear some strange knocking sound from the ice maker .
We never worked on this kind of ice maker before ,it looks kind of strange one for us
Any help would really appreciate