Repair Help

This unit is not defrosting, causing the evaporator to ice over. I have ohmed the defrost bimetal and the defrost heater and they are both within spec. I’m not sure how to force this unit into defrost or which board controls the defrost.

Not defrosting, checked bimetal and heater and they are good. Unit has a board at the back and board at the control. Which board should I replace for defrost?

I know this is a long shot, but I have a customer that says the washer makes a slight squeaking noise at the start of the spin cycle and the end of the spin cycle. I have been there 2 times and have yet to heat this squeak. I really don’t know where to start, other than rotor / stator. Tub supports are lubed. Please if you have any suggestions pass them on. I am going back out tomorrow for the 3rd time.

We need a tech sheet and wiring diagram for tis range. It is electric with double oven.
Thank you.

This combo unit has banging/grinding sound during spin cycle besides the drive pulley what else should I look for? Is there any videos of repairs similar on this type of unit that had this problem?

During the rinse & spin cycle the agitator spins wildly and makes an insanely loud screeching/grinding sound while whipping the clothes so hard and fast they stretch and if caught right, will rip. If I cancel the cycle and select “rinse and spin” it will rinse the clothes, but then during the spin cycle the malfunction will occur again. I then tried a “drain and spin” cycle which seemed to operate normally.

I need to diagnose the issue and identify the right part to replace.

Thank you in advance for your help!

I have videos if you need them.

This is a Maytag Bravos MCT

Technician checked water valve good all door switches fine .Pushed the pad no voltage comes the water valve.
what could be the problem if you have the schematic will help also?

Temperature in FF section is to warm, customer sets it on 38 degrees and it is 56 degrees. What should I look for?

gtw3300ask0ww Cold water was slowly running in in washer was not in use(trash in line), then one day customer find washer had been running water in for a long time(5hrs). Now water doesn’t run in , but washer only washes on a mini cycle

board, heater and defrost thermostat have been replaced. How do you check the defrost thermstat and the easiest way to replace it?

Fresh food side is not cooling well, it’s around 54 degrees. Freezer is ok. Put it to forced cooling and can see fan moving. Could it be board or sensor? How do I make sure? I need all the tips on how to find out or troubleshoot it. Thanks.

sometimes washer completes entire cycle normally. Other times it starts, tumbles 1 rotation and stops, then shuts off. Other times it goes through the wash cycle but when it comes to spin, it just keeps tumbling clothes back and forth while drain pump runs and never gets to spin speed. When it does this the estimated time remaining clock will stay on the same time for maybe 10 minutes before going down by a minute then it will take another 10 minutes to go down another minute. it will eventually shut off without spinning so clothes are still wet. We have run the diagnostic tests and all functions work normally. Also washer does not give any error codes when it does this.
We appreciate any advise.
Thank you.

How do you enter into defrost mode

Why won’t the service mode work? Is there a “trick” to it? Could a thermister cause this? If so which one and where is it located.

Any ideas? I watched the videos on the service mode and seems I am doing it correct.

Code11 shows up, which is the MCU. How can I check to make sure that is what is wrong. Kenmoe Elite HE4T

Customer complaining that they smell a burning smell. I ran it through a cycle and of course it worked great. They say that it pauses in the middle of cycle(mid 20s on dail) and it flashes pause, and they restart the washer. What should I look for. Thanks Chip

Freezer door won’t stay closed, gasket looks to be in good shape. When I got there I found the draw in the bottom of freezer compartment was sticking out in the way of the door. Fixed the draw where it was out of the way from the door from closing, but the door still wants to not seal tightly.

Preheated but after that when the ignitor gets red again to light the gas it doesnt preheat. Only couple years old. Ignitor is good. But the temperature will not pass 120F. Can diagnostic manuals for this unit

I have a GE Monogram I need to get the dispenser display removed to get inside to repair some broken pieces. However I am having no luck. Do you have any videos on how to remove the outer panel so I can remove the dispenser cover?

Customer had F-20 code. Replaced fill valve and customer claims that they still get code on normal wash only, not on quick wash. Unplugged unit and left for an hour than plugged back in. Same problem remains. Any ideas?

Dacor vent when you hit the button to retract it, the vent goes down THEN COMES BACK UP SLIGHTLY and continues to run the blower fan..?
I didnt see any switches near the gear raise motor .. Did i miss something or is it the control board?

went out and replaced the heater assy. due to no heat. customer calling back 2 weeks later getting an he error?

Stack washer/dryer washer won’t start, dead, no lights, dryer okay. control board fuse blown. replaced control board lights came on, tried to start, went dead, new control board fuse blown

Need tech manual please. Refrigerator was turning on and off. Now completely dead.

Thank you

correct voltage at terminal block. Turn on control. what ever cycle when start is pressed. control shows dryer operating. door switch, thermals and belt switch check ok. Don’t know where to read voltages at motor. and not sure where on control is the motor circuit.

Asko Dishwasher fills, clicks 3 times, flashes “delicate wash” after new inlet valve installed, old valve was leaking bad, new valve seems good fills to the proper level as far as i can tell but cycle doesnt continue. Tested resurculation motor that tested good and had continuity and their initial complaint was leaking which it no longer is leaking. drains fine, water switch and door switch seemed to be fine..?