0 votes
3k views

My whirlpool gold quiet partner keypad is locked. I held the air dry button for 5 seconds and it will not unlock. Pleasr help

0 votes
3k views

I have a Kenmore front loading washer, about 8 yrs old, that has had what sounds like occasional bearing noise lately during the spin cycle. Today during the final high speed spin there was a bang and the drum slowed right down. I think it broke something… could this be related to the bearings? When I turned the machine off the drum didn’t seem to have a problem rotating back & forth very slowly for a while like it usually does at the end of a spin. If it is the drum bearings is it an expensive repair? — if it is I’m wondering if I’d be better off getting a new washer.

1 vote
11k views

Hi,
I turned on the Lower drawer to my Fisher Paykel 2-drawer dishwasher and pushed the start button. Instead of engaging, it made a short beep sound, followed by several rapid beeping sounds. There weren’t any error symbols displayed.The upper drawer works fine. The lower drawer gave no indication of problems and worked fine the night before. Since that time, I have been using half of a dishwasher for several months. Help!

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
8k views

Hi,
I looked at the titles of repair videos in your list. There are 3(I think) available LG Dryer repair videos that may be the issue, but the model number is different from mine……
1) Does that make a difference?
2) Do I have to purchase each video to find out how to fix it?
3) How can I tell which video will address my dryer’s problem?
4) I saw video titles for other brands of dryers (GE, Samsung, etc). Are the different brands and models so different from mine that one won’t apply to the other?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

When push the start button it will start but soon it stopped and giving an error code LE

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

the water dispenser on my Monogram refrigerator stopped working. I changed the filter and pressed the dispenser arm for two minutes. ice is being made. what do I do next?

0 votes
4k views

The water line on my Whirlpool ice maker froze (refrigerator model GI7FVCXWY02). I have removed the ice maker to let it thaw. Why did it freeze? How do I stop it from freezing again when I put the ice maker back?

0 votes
4k views

I have a Kenmore Elite Refrigerator with ice maker. The ice maker makes ice, but will not dispense it. It rotates and you hear it rotating, but no ice comes out and then it gets jammed in the bottom and then melts. The water dispenser works fine.

0 votes
3k views

We have a Kenmore Side by Side with water and Ice dispensor on the Freezer door. THe Water won’t come out of the dispensor but it does make ice in the ice maker though. How can we unclog the water line to get water out of the water dispensor

0 votes
3k views

I have a 2009 Samsung 28.5 cu ft refrigerator with french doors and ice and water service on the outside of the door. It is model #RFG297AARS, BOM # XXXXX with TWIN COOLING Plus. It has a SPACE Icemaker. The compressor is BK190C-L2C.
After just over four years of operation, the ice maker stopped producing ice. The water filter has not been replaced for a couple of years; however, it is not clogged. The water dispenser on the door still flows as it should. I removed the filter and the water still flows as it should.
The ice maker started slowing to the point that we were getting only a couple of blocks of ice at a time. Then it stopped producing completely.
I have tried holding the reset button for ten to twelve seconds with no results.
How should I go about doing any further test to determine the problem. I have not replaced the filter yet but plan to do so.

1 vote
4k views

Fridge is 33 degrees freezer is 31. Tested sensors ohm out good fan motor will not start up. I believe it is the board but would like to put fridge in diagnose mode to verify. Not familiar with digital exterior display diagnosis mode, unlike Jazz board models. Can you please help?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

I have an Electrolux refrigerator model EI26SS55GWO. We have Reverse Osmosis water going to it which is filtered about 6 times more than the refrigerator filters yet it seems in order to keep the ice maker working properly the filter needs to be changed about every two months. Is there a way to by pass the filter?

1 vote
4k views

Recently did sealed system work. Because heat exchanger was leaking refrigerant. Replaced evaporator and heat exchanger. Heating loop below the fridge looks perfect. Condenser clean. Condenser fan motor running. Evaporator and all other fans seem to be running and everything is plugged in and running properly…
But the display is flashing certain temperature control bars. Which if I recall correctly is an error code. The FRZ light is flashing and light bar 3/4/5/6 keeps flashing in numerical sequence. What is this error code indicating?

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

Continental refrigerator: This is my first time with a unit like this and there is no wiring diagrams , the refrigerator thermostat is open (satisfied), the evaporator is frozen with build up.(defrost failure) not sure, how timer work or wiring path. I have a strong feeling the timer has issues. I would appreciate any advice unit, as well as defrost system and wiring diagrams, you may come up with. Also, light in top half stays on, (refrigerator compartment) Thank you

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Gas dryer keeps shutting off. I can sometimes get it to complete a full dry after a few start/stop cycles.

When I press ‘start’ either on auto or timed cycles, the dryer will start for about a minute, then stop. Or when the start is pressed, the relay clicks and the drum (I have the top removed) moves about a 1/4 inch. I then press off/then start buttons until the dryer starts (each unsuccessful try the relay clicks and the drum slightly moves). It may take ten off/start button cycles to get it to start again. After which, it may stop after 1-5 minutes or go the whole dry cycle. Sometimes if the start/off button can’t get it to start, then pressing the control button to turn off the lights and then control button to turn on lights and then start after that sometimes works.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Not making ice properly also the water pressure through the door is very weak.

0 votes
2k views

Just need the wiring diagram for gfe28gskfss. I need to find out if the ice maker goes through any boards more specifically.

Thank you

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

We are working on a 2 year old ge top load washer that will not pin out at the end of cycles.

We have tried a used pump and board, new lid switch and pressure hose.

All hoses, pressure dome and tub are all clean.

This is the second washer of this style were we have run into this problem without being able to figure it out.

It pumps out the water for aproximately 10 minutes before coding out or spinning.

Error codes 16 and 18 (slow drain) keep on happening.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

The Frigidaire front loading washer will not spin. it let in just a bit of water and then nothing happens. ive unplugged it and checked that the water supply hoses are not clogged. what do i do next?

0 votes
3k views

My Kenmore 110-75922401 dryer gets too hot and the timer does not work. I have replaced the high limit and internal bias thermostats and cleaned the vent system thoroughly.

0 votes
3k views

I have a whirlpool duet electric dryer. model GEW9200LW1 The drying sensor does not seem to be as accurate as it once was (purchased 2004) the clothes are sometimes still damp. Can the sensor be cleaned? I read somewhere that fabric softner can cause this problem

0 votes
3k views

Indicator does two flashes next to thermostat in between pauses. Checked DSI (oven spark module) and it tested good. Even popped a new one in for good measure no change. I’m suspecting the thermostat it also has some grease in it which I know Viking addressed with a kit. Can you guys get me the diagnostic guide MOST IMPORTANTLY THE FLASHING ERROR CODE guide.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

I have a samsung moisture sensor dryer that just stopped coming on. Worked find this morning went to dry another set of clothes and not turning on.

0 votes
4k views

My Samsung electric dryer is giving an HE error code. I have replaced the thermistor and the thermistat. The dryer is making heat. I have cleaned out the vent all the way to the roof. What is next?

0 votes
3k views

not heating

0 votes
3k views

My freezer works but not fridge. Bottom freezer.

0 votes
3k views

My microwave won’t heat.

0 votes
2k views

I have a Kitchenaid combo microwave and oven … KEMS309bssoo. The microwave runs fine but when the cooking cycle is complete the unit turns off the light and cooking power but the fan continues to run and the bell does not ring. You have to open the door or press the cancel button to get the unit to completely shut off.

-1 votes
4k views

I’m getting F21 flashing on my washing machine, Its a maytag 3000 series.

0 votes
5k views

water works and dispenses but doesn’t make ice.Took ice maker apart no water in tray

  • Guest asked 8 years ago
  • last active 8 years ago
Showing 2161 - 2190 of 9k results