0 votes
3k views

The led on the motor is not working so I can’t read the error code. The washer will only fill and drain. It will not agitate or spin.In The test cycle also it only fills and drain s. I need a service manual and any videos.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Two and a half years old, stopped cooling suddenly back in March. No error codes. Coils clean, compressor fan worked, compressor worked (could hear), freezer fan worked – but not cooling at all. Unplugged while waiting for LG technicians for three weeks. After three weeks, I looked up at compressor, tapped compressor’s high pressure side with screwdriver handle. Plugged it back – it got proper temperature 0 F freezer / 37 F fridge in two hours. Worked fine up to beginning of September.

Symptoms now: too warm – 28 F freezer / 48 F fridge.
What would you suggest me to test?

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
3k views

No water I checked the primary valve its good but no voltage. I checked the ice and water valves inside the door. good and getting voltage. Not sure how this works but the circuit diagram shows the Pilot valve is powered from the main PCB and the ice and water valves are powered from the PWB Assembly Dispenser board. I have water to the Pilot valve ( The valve in back of the frig ) I emptied the water in the reservoir in the door. But still, the pilot valve is not energized. Do I need to get a PCB board or can you tell me why I get no water?

Thanks
Bill
Neighborhood appliance

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

The bake & timer button on my elec stove doesn’t work. model GY397LXUS03

0 votes
2k views

My Frigidaire range stove burner not shutting off,I changed stove burner switch but still the same problem.

0 votes
3k views

I have a kitchen aid stove. I tried to remove the oven door without placing the pins needed. It came off but the hinge came with it. how do I fix it?

0 votes
3k views

My GE oven will not heat past 100 degrees.

0 votes
4k views

Have a unit with no display when powered up. Display will come on when microwave door is opened and clock can then be set. Lower Oven can then be programmed and will start to heat as long as microwave door is opened. Lights also get very bright while oven is heating (oven and microwave lights both come on when either door is opened).If microwave door is closed relays can be heard clicking then display and oven both turn off. If microwave door is opened then clock display comes back up; although if you wait awhile before opening the door it just reverts to power failure mode. Relay board was already replaced to no effect.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views
0 votes
3k views

Is this one like the Samsung duel evaporator models? Is there a kit for this one? I need a service manual to disassemble it. Are there any vidoes for this one? Is the best way to defrost this one to unplug it a few days?

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
4k views

My Kenmore washer is displaying an e24 error code.

0 votes
13k views

I have a Kenmore Elite Dryer and I keep getting a F code. I have cleaned the lint trap but it keep stopping.

0 votes
4k views

Kenmore Elite refrigerator makes buzzing sound which stops when we open the door.

0 votes
3k views

I have a GE spacemaker microwave the oven is not heating up to make tea we had a power spike the tea hardly heats up even after 6 seconds.

0 votes
3k views

Dryer runs for about 20minutes, then quits turning. Clothes aren’t dry

0 votes
3k views

I just need to know which belt fits my Whirlpool dryer. Im not sure of the model number but the belt itself says ” 950ET 09E 12-0″ on it.

0 votes
3k views

Dryer smells like it is burning. I have cleaned lint trap, taken the hose off and cleaned it. Still smells like something is burning within 2 minutes of turning dryer on.

0 votes
3k views

I am looking to replace the heating element on my dryer. I am not sure where the element on this unit is located, any ideas?

0 votes
3k views

I have a maytag Neptune gas dryer. I am having trouble finding an adaptor for the gas line to connect to the dryer. The part coming out of the dryer is 5/8 and the gas line end is 3/4. Can I get something from you that will make this work.

0 votes
3k views

Seems like too much pressure when ice maker is filling and water splashes out and into ice maker compartment.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

Originally, the washer had an LE code. I tightened the bolt in rear that holds rotor in place (4040FR4051C). After that the washer would agitate clockwise and spin just fine, but everytime it tried to agitate counter clockwise it would lock up, the magnets where so strong I coulndn’t even help it turn with my hands. So at this point, I proceeded to change rotor, then stator, with the same result. All the wires looked good except for one ground wire that I repaired. Any Ideas or suggestions?
P.S.—-What is the easiest way to get broke bolt out of tub shaft (4040FR4051C), as I have now successfully broken the bolt off from taking on and off so much I guess.

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
3k views

The freezer frezzes up in 2 days and dont defeost

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

FF & FZ not getting cold enough. I would say because the compressor is not staying on long enough. Its a linear compressor. I measured the voltage going to it. 220v when starts and slowly rises to 350v then shuts off o volts. 5 minutes later will start again. compressor is normal temp not burning hot. looked at the main board, its giving 6 flashes. Evap. & Condenser fans stay running. Only the compressor shuts off. voltage at the wall outlet is normal 120v.

0 votes
3k views

My fridge evap. Is not defrost is full of ice this is my first time working on this unit I assume this is controlled by a thermostat. Any other devices or thermostat? I see a aluminum evap with wires inside? Help please

  • Guest asked 7 years ago
  • last active 7 years ago
1 vote
10k views

HOW DO I TROUBLESHOOT THIS? I SUSPECT BAD WATER VALVE. NO WATER IN TUB AND COMING UP WITH U6 ERROR CODE. THANKS.

0 votes
3k views

My Frigidaire Fridge Model LGUB2642LF2 is having problems with the internal lighting. Both upper fridge and lower freezer lights all went out at the same time. Have removed the lights and tested with a continuity tester and they are good. Also, one of the upper lights appears to have melted the roof of the Fridge open from what appears to be excessive heat. What would be the most probable cause for them to all go out at the same time? Have snapped the switches for all the doors and no result.

0 votes
3k views

My fridge has shut down. We tried to shut the Replace filter light off by pressing on Options and Measured Fill. The light replace filter went out but now the freezer and fridge aren’t working.

0 votes
4k views

Shuts off and gives error codes.

1 vote
4k views

The dispensor control board keeps blinking 0 37 no led lights on in fridge and freezer. Unit still running and cooling. Able to get lights back on but then go out again. Nothing dispensing either.

  • Guest asked 7 years ago
  • last active 7 years ago
0 votes
3k views

GE Profile microwave will not turn itself off. When the door is opened, the turntable starts to run and the oven is on Tried closing the door three time as suggested on a website — no luck

Showing 2251 - 2280 of 9k results