Repair Help

The machine is making noise during the spin cycle. Now it’s completely shutting off in the middle of the spin cycle. What should I fix? It is showing an error code of 3E.

We have a dishwasher that, what ever the remaining time, adds additional time. If there is 40 minutes left it’ll then add more time and show it has 90 minutes left. This happens with every cycle. Main control board has been replaced and the same issue continues. Any suggestions?

The washer makes a clicking noise on low spin only. When the drum is up to full speed the sound goes away. It is draining normal and doesn’t sound like it is coming from the pump. Customer states ticking noise was not there before main bearing was replaced by seperate company. Thanks, Steve

Hi,

I check out the thermistor and it’s ohms out okay. Thinking about the control (diffuser) but I didn’t want to go any further due to the cost of these parts. What do you guys think?

Thank you,

JAN
Barney’s Appliance

Freezing in the refrigeration compartment

Ld error says drain pump issue or drain clogged up. No clogs found, drain pump works great. When any cycle is selected it drains and keeps draining then the LD error. The main control board was changed out not to long ago. Any ideas?

the timer looks like it has a burnt mark on it.
but no water will enter.
nothing happens at all.
the dryer works fine

GOOD MORNING, I DID NOT GO ON THE CALL, BUT I AM TOLD THAT THE UNIT IS NOT WORKING AND IS MAKING A GROANING NOISE. ANY INFO WOULD BE GREAT, AS I HAVE NEVER WORKED ON A JENN AIR DISHWASHER. THANKS, TODD FROM NY.

HI DO YOU HAVE INFO ON HOW I CAN REPLACE THE FRONT GAS KNOB FOR THE BURNERS

Customer said the ice maker was making noise and no ice was being made. Tech did not hear any noise. Any suggestions as to where to start looking for problems in ice maker, being that there is no ice maker assembly and it’s all in individual parts?

Dryer wont start because, even though the door is closed, it reads it as open. The Main Contro Board was replaced and the same thing still happens, any suggestions as to what could be causing this issue?

Can you send a pdf on how to repair the icemaker? I understand you cannot buy the Icemaker, repair only Thank You

Hello
I have a GE gas range. The customer complaint is in self clean only, it takes too long to get up to temperature. The broil is on only in self clean, the bake does not come on at all even after 15 minutes. Is the bake supposed to come on at all or intermittently ? Thanks in advance

the unit will fill and drain.
the agitator will move freely when I try to turn it.
there is a board on top of the motor that Hase a blinking red light.
also the red and yellow wires coming from the motor to the transmission do not have power

error code e- 01 and e 24
drain pump has been replaced and it will not go the complete cycle

evaporator motor was replaced the adc electronic board was replaced and the damper assembly was replaced and frigde is still not getting cold it’s cool, not cold enough
please help

I’VE HAVE DONE EVERYTHING I CAN THINK OF ON THIS UNIT AND ANOTHER ONE JUST LIKE IT.

I need a servive manual that tells me how to disassemble and clean out wash arms and sump area of this dishwasher, I have a parts breakdown from my supplier but that doesn’t explain how to disassemble, i have cleared a lot of the jets using a bent hook tool, washer worked better for a week ???? any suguestions??
Thank you Joeclening uot jets

GOOD MORNING. I DID NOT CHECK OUT THE UNIT, BUT I AM TOLD THAT IT WILL FILL AND THEN NOT START THE CYCLE. ANY INFO WOULD BE GREAT, AS I AM NOT UP TO SPEED WITH FRONT LOADERS. THANKS, TODD FROM NY.

Hi,
I am working on a g.e front load. Maybe about 3 years old.
I believe the drain pump is bad, but the problem is I never worked on this particular model of ge.
Normal I would unscrew the 3 screws in the back of the lid and then pop of the top cover….
But this model does not have any screws for you to remove.
There must he a special way for me to take of the top panel ??so I can disassemble the machine for repairs.
Any information helps 🙂

Have remaining water after the complete cycles on watch. When we shake the drum. We feel lots of water remaining with in the drum. Is this drain motor problem?