Repair Help

I am not getting any display option. And it’s causing the unit not to cool. It is not on Sabbath mode and I am getting power to the display.. What else can I look for

I have a Whirlpool French Door Bottom Mount Refrigerator. The icemaker has a slow drip out of the front of the icemaker heater cover. The water slowly drips down into the front ice bin. the Ice bin in the front door builds up with ice and eventually the water starts to run out of the opening of the front door and the water and Ice dispenser unit installed on the front door.

How do I stop the water from dripping out of the icemaker front cover?

the customer said that when the machine goes into spin it sounds like a truck

I HAVE TWO, OF THESE UNITS, WITH SEALED SYSTEM PROBLEMS. PREVIOUS TECHS CUT NUMEROUS REFRIGERATION LINES. I NEED INFO ON PUTTING UNITS INTO DIAGNOSTIC MODE, SPECIFICALLY IN PREPARATION TO FINDING LEAK OR LEAKS AND RECHARGING. I NEED TO GET THE REVERSING VALVE IN THE CORRECT POSITION, ETC

THE BURNERS WILL CLICK

Hello,
I followed your video for diagnosing my Kitchenaid (ksrl25fxms02) refrigerator’s ice maker as it had stopped producing ice.
I want to thank you for the clear presentation of the material. If was a refreshing change to have some clear, concise steps on interpreting the optical diagnostic codes and conducting the manual test of the ice maker’s harvest cycle that did not leave me wondering if I was doing something wrong.
Unfortunately, I am still getting mixed results that lead me to believe that perhaps the ice maker and the optical boards may both have problems.
I’m hoping that your experience will make some sense of what I am seeing and help me determine the best course of action.
After viewing your video, I unplugged my refrigerator, jumpered test points T and H then plugged the refrigerator back in and depressed the switch in the door so that the beam path was unbroken. I was surprised to see that the blinking led went from the 2 blink, 1 second pause code to a solid light. Previously, it continued the 2 blink, 1 second pause code no matter what i did. The harvest cycle never started during this first test, which led me to believe that the ice maker itself was bad.
I decided to repeat the test in precisely the same way and got a different result this time and a few additional times. In these subsequent tests, the led continued to blink in the 2 blink, 1 second pause pattern as it had before I followed the steps in your video and did not go to a solid light
This behavior leads me to suspect both the ice maker and the optical boards.
I wonder if you have observed this behavior before and if it is to be expected or if you have some thoughts on what the next steps should be.
Hopefully this makes sense.
Thank you

Customer called said the box would show sy. Ce. Then the main board would start clicking but she said box was still cooling. The f code usually means the main board is faulty.

it will agitate and Darin but it will not spin at high speed

The compressor is running and pulling 1 amp. the condensing coil is clean and both fans are running. I installed a service valve, on the suction line, at the compressor. when i attached the gauges it immediately went to 29 inches of vacuum. I unplugged the unit and it stayed at the same value. in your opinion what does this indicate. i’m waiting on r134a to be delivered so I haven’t tried adding any refrigerant to this point.

do you have a video on how to replace the boot or bellow?

I had a customer with a Kenmore standup freezer and not getting enough cold on both food compartment and the freezer. We just replaced the control board and still having the same issue.
Your help is very critical. please assist.

the customer states that when the machine is cold or warm then she gets the f01 but if it’s on HOT the machine works fine with out an error code

at first the ignitor would not Evan glow.
I checked the thermal fuse it was OL so I changed it now it will glow but will not light .
I checked the thermistor it is OK and the ignitor has 60 OHM
please advise.
the customer said they had an F70 error and now it will heat at all

Need a electrical schematic for this refrigerator. I’m not getting power to the evaporator fan.

I did some research and found a lot of different options… Oh by the way, I hate LG products, and I’ll never work on another one.

What are the most common problems causing a GE profile to no cool properly ie 33 degrees in freezer and 50 degrees in refrigerator

Does control board operate every on the refrigerator?

The dishwasher blue light will come on like it is going to start the cycle. I hear no noise and then the blue light goes off. when I open it, the cancel, drain light is on.

The above washer is leaking from the tub seal and is loud in spin. I have not done this repair before but I’m thinking it is going to need the Kit support assembly. Part number WH16X10185. Has anyone done this repair? I would like to know if there are other parts I should be replacing as well. Looks like it has been leaking for a while. I’m familiar with changing out the mode shifter in other GE models but this is not quite the same and I did not find any good info on this repair. Thank you for any advise on this one.

why does Kenmore upright freezer top shelf have a big big frost built up none of the other shelfs do this this is a very simple unit manual defrost no interior fan.

replaced control part w108900094 and part wp12999401b and that did not solve problem can you help ?