Repair Help

We can turn the fan on but when try turning the heat on nothing happens i look at the furnace a the light blinks 3 times…

This started after a long overdue water filter change. I know that water comes through the filter on its way to the icemaker. When I hear ice drop and then the icemaker refill with new water, a puddle forms under the front left corner.

The coils not iced over, the fan is working. the damper control will not open. The front panel always shows 70 it will change but goes right back to 70.

hello

I have a kitchenaid dishwasher that starts to fill and stops before it reaches the float. the float moves freely and the float switch itself is good and electically works

any idea where to go next

thanks
james

Ice maker works OK, It makes ice.
Sometimes the ice dispenser is working but again sometimes it stop working and can’t hear any noise when it doesn’t work.
What can be the problem?

since joining this site I’ve given at least 5 model #s and every time it comes up as” no results found.” just now I typed in # kgsa906pssoo which is a kitchenaid gas stove, I don’t understand why I get no results?

I saw a video on YouTube on how to fix GE’s water dispenser. My question is before going in and unhooking the water valves, do I need to turn off the water?

-Jin

can you suggest a video to describe what could be wrong? This only happens during the spin cycle.

I own an appliance repair company in Texas. I have found the upper rack may disengage from the rails when the
customer pulls the upper rack out to load or unload the dishes
Wheel axle breaks and causes upper rack to fall when pulled out on many of the dishwashers.
Any suggestions would be greatly appreciated thanks in advance James.

Yesterday I was using it in bulky items cycle with 3 tennis balls to help fluff, and there was a beeping sensor going off while drying – but no error message. I opened the door and switched the cycle to normal. It worked fine and follow up “touch up” cycle also worked twice. I went to use the touch up cycle this morning,mand the light on the inside of the dryer won’t come on, and it won’t start. All of the display cycles light up and seem to work properly, but won’t start. Just gives me three quick beeps as though the dryer door is open. It shuts nice and tight, and the door catches seem to be intact and sturdy. I have had the occasional problem when after starting the dryer, about 30-45 seconds later it would shut off prematurely. When restarted it would go through entire cycle. I’ve ignored that problem since it’s very sporadic. Could they be related? I don’t know if I need one or two new door latch kits or a new door switch?

making load noise during high spin

how to trouble shoot, the ice maker that is not making ice at all

badger 5 plus

Hi, I have a Amana gas dryer and the dryer won’t turn on. Every time I push the start button, it will trip my house circuit fuse. I tried plugging in a different outlet it will trip that before I even push the stat button. I unplug the wire on the machine that spins the drum and it will also trip the fuse, (I mean with some wires unplugged and pushing the start button it will still trip the fuse). Do you have any ideas where the issue is?

Hi I have water leaking from the light of my bottom mount freezer drawer. it does not seem to be constant but there is always a build up of ice. I have been watching other videos and seems it might be a clogged drain plug. someone elese also said it could be in need of an air filter replacement. I can’t find the specific model on your site so I was wondering if you could tell me which video to watch that would have a similar model to mine. Thank you!

can set clock for 1 min cook or 5 min cook magnetron wont kick on until 45 second run time help

I have a Amana gas dryer and the dryer won’t turn on. Every time I push the start button, it will trip my house circuit fuse. I tried plugging in a different outlet and it will trip that before I even push the stat button. I unplug the wire on the machine that spins the drum and it will also trip the fuse, (I mean with some wires unplugged and pushing the start button it will still trip the fuse). Do you have any ideas where the issue is?

do you have a video on replacing the drive belt for this washer

Have LG refrigerator with ER 1F code. Fan motor for icemaker runs then shuts off.
Has anyone ran into this problem?

Viking Range she wants to convert from NG to LP. Parts are no longer available and no longer even listed. The model number is VGR36-4GDVB. I have not seen the range yet. Is this even worth trying to convert and does anyone have the orifices in old stock for this range? The advise I was given by the Viking distributor was I would have to drill my own which I have not done or know how to do. Thank you

The oven control board/clock on this unit shuts down completely and goes blank when doing a self clean but comes back on as soon as it cools down, and shows that there was a power failure. Pushing cancel resets it and then it functions normally. I don’t see a cooling fan in the parts diagram and didn’t think to look for on when I was at the appliance. Would this be a control board problem or a preservation mechanism built in to the appliance? Thank you for any advice.
Whirlpool Oven GR448LXPS 2

Maytag Neptune washer model# MAH4000AWW – starts and stops:
This unit has a timer and a motor control board and a push start button. When you place the timer on any load size and press the start button, the washer begins and fills with water. Once filed the unit shuts off. It does not advance, the timer is not ticking like any egg timer or moving through the cycle at all. If you press the on/off button again it will fill with a little water but stops and turns off.
The motor control board and the time are both expensive. Too expensive to replace both, but i am having trouble separating out which one it may be. I am not looking to the motor because the timer is not advancing at all or should it be, I am not sure.

replacing a thermister in a samsung wf393btpara /a2 Is this a simple repair or do I have to take off a bunch of stuff?
Is it a just take the back off and there it is?
I have a TE error.

I have had two compressors this week that would not start. I usually place a 3n1 on them to test them and then replace the OEM start device. On these two, one a frigidaire and the other a Jenn-air, the OEM parts would not start the compressors. I ended up leaving the 3n1 kits on them. Is this the only option short of replacing the compressors? I don’t do sealed system work. Thank you in advance.

CANT REMOVE DISPENSER IN DOOR

What is the part Number for the Drain Repair kit for this fridge

Thanks,

Patrick

The ice maker is not making any ice. The feed tube in the very back of the ice maker appears to be clogged with ice. On the back of the refrigerator is a water line inside of a rectangular piece of plastic. It appears to lead directly into the feed tube. How do I remove the feed tube so that I can get the ice out of it? I would think that I have to clear the line before I fix any additional components (such as the switch at the bottom of the refrigerator which activates water flow). I thought about turning the refrigerator off but then I might ruin the contents of the freezer. Also once I get the tube out of the refrigerator what is the best way to clean out the tube? Hold it under warm water? Please advise.

I am replace a control board on a GE wall oven model JGRP16GEP1BG. Problem is the instructions to wire the cooling fans are completely useless, the wiring diagram came with 3 sheets. The first sheet has some useful info on installing jumpers and the bake and broil relays, but the next two pages were from a front load washer on installing a soap dispenser, these were all stapled together! There is a third relay which I will have to do a live test to see what that relay is doing if anything.

my refrigerator isn’t working not cooling in the freezer isn’t freezing anything you can hear the noise like it’s working but is not doing a thing

looking for the replacement ignitor caloric range RJP363 has original round ignitor.0068016 this was the one ignitor that had the different mounting bracket in the kit to convert it to flat ignitor . this was never converted. There is a flat ignitor replacement but it doesn’t have the brackets in the kit i need 0309150 kit