Repair Help

The dispenser pump motor runs but it’s not measuring and adding the soap.
The blue soap dispenser is in it’s proper place. How do I check if the dispenser pump is pumping?
I’m referring to the w10842325 dispenser and pump assembly.
Could the hoses be clogged?
Please explain In as much detail as you can.
I notice when i run the diagnostics that though that small pump motor runs it doesn’t turn on the water valve. I suppose that the water it pumps into the dispenser comes through the mixing valve.

Could this be a mainboard issue?
Bake relay P7 Yellow and P2 Black 120 ac when the oven is off and 0 ac when it is on.
Broil element K2 relay also 120 ac when the oven is off.

In the diagnostics mode the washer in the spin test, the clutch engages ok but the motor does not work. In the agitate test the washer fills but the motor does not work.
I can hear a momentary relay on the board and the motor seems to try to energize for less than 1 second, but nothing else.

Hello, I have a speed queen dryer model ADGE9BGS113TW01, serial number 1612045509, with the problem that it does not heat up.

It doesn’t show any code on the front panel.

I already checked the thermostat, it gave me 4400 amps, so I changed it for a new one and it still doesn’t heat up.

You can help me to know what else you can have.

The freezer section is cooling but the fridge compartment is not cooling.

Board is flashing 4 times which says it is a locked compressor, the tech tested the 3 leads on the compressor, they all tested 12 ohms each. He tested them to ground and that passed. Control board has 3 wires going to the compressor, each wire to ground test 125 volts dc. Is this AC voltage that goes to the compressor or DC. Is it the compressor that has failed, or the board?

Customer put a standalone thermometer in refrigerator section. Temperature goes from 50 to 37 degrees. Is this normal or does the main PCB need to be replaced.

Could a faulty UI cause the main control board to short circuit and fry?

My technician replaced a faulty control board and pressed the start button to go into service mode – the board was immediately fried, only after pressing the start function.

I’m reaching out on this one because I’ve already lost two control boards for this repair. 🙁

Hello, I have a Speed Queen AFNE9BSP113TW01 washing machine, which is presenting me with the P5 error code, this appears after having changed the Mixing Valve. Could you tell me if this is connected and what do you recommend I do?

I followed the instructions in the Video on your page for the Speed Queen AFNE9BSP116TW13 washing machine, because I did not find the specific video for my washing machine.

Hi,

The refrigerator is cooling but the freezer is not reaching the correct temperature (cooling but not freezing). There is ice build up on the right side of the evaporator coil (not on the evaporator itself). Both fans are running (condenser and evaporator).

To whom it may concern,
I have a whirlpool WRF757SDEM refrigerator that recently has a loud noise coming that appears to be coming from the top section. Last year I replaced the evaporator fan and thermostat as the unit has frozen up and stopped cooling. After that fan was replaced the unit was very quit and running normally.
Recently ( past 3 days) it has gotten very loud at times with a slight vibration. At times, the sound is very loud, but then it gets quieter; almost to normal levels.
The top unit is cold and maintains temperature, there isn’t any issue making ice and everything is cold and frozen in the freezer.
I am wondering if its an issue with the evaporator fan and if that needs to be replaced again.
Any and all assistance would be greatly appreciated.
Kindest regards,
Kris

My washer is hard to start. I put it in diagnostic mode and get codes F0 E3

I need to replace display control assembly some keys on the keypad are not working need service manuel

Hello,

Our fridge is working great as far as we can tell. We have owned it for 3+ years.
I am writing because I have noticed that when the compressor is on, or at least I think it is on, and at a higher rate of speed that it is a bit loud inside the unit and has some variation in the motor sounds when it is running – not smooth. I would like to send you an audio file that I created of the sound so you can see if things seem ok.
I could wait til it breaks but the unit is used in a luxury rental property and we don’t want a large failure in the middle of our rental season! Hope you can understand that I am being proactive vs. reactive.
I believe the fridge has made this sound for a while but am not sure if it is getting worse? Unclear to me.

And, if possible, I would like to know how to clean the coils of the fridge. I hope it doesn’t need to be rolled out to do this. Thanks.

Jeff

change the control board /water valve and door latch water presuer is ok but still code is on

I have ohmd out the unbalanced switch which tested good. I can hear the lid switch when the washer tries to go in to spin mode. About 15 seconds later it displays the Er UB error. The machine is level with no broken springs. Wires to the swich look fine.

GE Dishwasher Model GDF530PGM0BB
stops mid cycle, all lights flashing, turning power off resets unit to normal,
run thru cycle, repeats problem

can you guide me to locate video for Frontload Dryer to access these main control board to replace it.

The broil and bake igniters are not turning on.
The oven chimes when I switch it to bake or broil but the igniters do not glow hot. Could the main circuit board go out? This is a very popular oven and brand. I could not find it on your website. When will you have a video on this range?