Repair Help

I need to know how to replace the evapartor fan motor

hi, my dryer was working fine up until i moved it in my new home. it blows cold air. i was wondering if it’s because it’s not getting enough electricity maybe, because i have a 3 prong but only two are actually plugged in (tried to make it fit in a four prong socket.

I need a service manual for this model. Is the problem in the board?

I’m trying to connect a 3 prong cable to a maytag bravo. Both the green and white wires terminate at middle terminal. The ground wire seems to come from internal harness. Do I still need a jumper ground wire?

CHANGED OUT A BAD ICE FAN ASSEMBLY, AND MELTED ICE THAT WAS ON THE LEFT TOP OF EVAPORATOR COILS. WENT BACK OUT TODAY, AND THE ICE WAS BACK AND ALSO THE WATER IN DOOR DIDN’T WORK. I THAWED THE ICE AND AFTER I DID THE WATER IN THE DOOR WORKED, SO I GUESSING THE WATER TUBE IN DOOR WAS FROZEN AS WELL. WHAT COULD BE CAUSING THIS CONSTANT ICE BUILD UP ON TOP LEFT OF THE COILS?

The control board is receiving power.
I thought maybe it’s a bad control board and it’s not powering the touch panel to start the unit so I replace the control board and I still have the same issue.
I’m not getting power to the touch panel to start the unit.
Door switch is also not getting any power.

Our Maytag washing machine has a leak. We have changed the hot and cold water hoses and that did not fix the problem. What should we look for next?

GE Model JVM 1540SP1SS, low power microwaves when door closes, hum/buzz heard. fan nor turntable operates,tap water in glass mildly warmer after counting 30 seconds with door closed, but no time on panel. Open door, press “Add 30 Seconds”, place new glass of tap water in microwave, close door and press ‘Start’. Fan and turntable operate. Hum/buzz not noticeably louder with fan and t-table operating. After 30 seconds, timer sounds, fan turntable stop, but hum/buzz continue. Open door immediately and tap water notably warmer.

I have Microwave model HMV8051U/01. It’s worked fine until recently. Now it doesn’t microwave. Display and interior and exterior lights are working. I have tried the lock / unlock routine several times but no good still. What do the display icons mean? There is not a picture in the manual. When I push 1 minute cooking it sounds like it is working but food doesn’t get warm or hot. There is an icon that looks like a rainbow that comes on.
Thanks

GE microwave oven is malfunctioning. With door closed and nothing set, it hums and the magnetron is definitely putting out. Turntable doesn’t turn and interior light doesn’t come on unless I set the timer, in which case the light comes on and the turntable turns. But, when time to stop, it beeps as normal at the end of the cycle and the turntable stops and the interior light goes out but the magnetron is still on and it is still humming.

Nothing will stop it except leaving the door ajar (and the light come on with the door open) or unplugging the unit. The clock works and I can (supposedly) set the power level and the timer for timed cooking, but as I said, when time to stop, the magnetron keeps running. I tried leaving it unplugged for a half hour hoping that would reset it, but it did not.

Edited to add: Everything on the touchpad seems to work correctly, but the magnetron will not turn off unless we leave the door open or unplug the unit.

GE Over the Range Microwave oven, model DVM1850DMBB

The turntable inside the microwave oven continues to turn. won’t stop.

Maytag top load washer makes a constant loud noise when washing or rinsing.It does not make the noise when spinning however when spinning it starts and stops jerking back to spin and never goes into the fast final spin that gets all the water out of the clothes. It does not leave water in the tub however.

iI have a LG Tromm washer, it will tumble in both directions but when its time to spin it doesn’t move and makes a racheting noise.
Help ?
Everything is soaked because it won’t spin to drain any water.
could it be the drain pump ?
wouldn’t it need to start draining before the spinning would start ?

We have a Whirlpool Cabrio Model WTW6800WL1 (bought in 2009). Sounds like it is taking off during spin cycles. Seems to be working but so loud can’t hear phone, TV or wash at night when we are in bed it is so loud. Repair man said he was an expert and our home maintenance insurance won’t fix a “noise” issue, even though the repair man said it was something to do with bearings.

What is the possible cause if the washer will not spin in the spin mode? There is a racheting sound but it won’t spin.

Our Whirlpool model WFW9150WW00 washer cannot complete the cycle. The washer cannot – at least to me – achieve a balanced load so it can spin the clothes prior to ending the cycle. ANy suggestions?

This unit pops the breaker if the oven and more than one burner is going. I checked the current at the breaker with the oven and two burners and it is 39 amps. The breaker is 40 amps. The installation sheet says to use a 40 amp service.

What’s up with this?

I need a wiring diagram. I traced the voltage loss to the relay but can’t tell if the coil voltage is right.

I have a model GHW9300PW Whirlpool Duet front-loader washing machine. It had an F02 (drain problem) error code & I had to remove the front panel to get the door unlocked to remove the laundry because it wouldn’t reset to finish the draining process.
Best I can tell at this point, the drain is not clogged. I plugged the washer in again today and was able to get the drain/spin cycle to start (it added water & locked the door), but after that I could only hear a buzzing sound. The drum won’t move & it won’t drain.
Any suggestions on what the problem might be?

I have a Whirlpool quiet partner 3 model number GU2400XTPB3. The rinse cycle light keeps blinking and the time has — across it. I have reset the main circut breaker ( nothing) I ran the hot water in the sink( nothing). It will not clear or start the cycle. Help.
signed Susan

I have a whirlpool quiet partner IV, and it has recently started getting ‘stuck’ at a number points in the cycle. For example, it will say it has 72 minutes left for about 20 minutes at a time, stay on 48 minutes for 30 minutes…etc. Its taking about 3 hours to run the dishwasher even on quick cycle. Anything I can do to fix?

I have a Whirlpool Quiet Partner III dishwasher, model GU2548XTPS6 that has suddenly stopped working. I usually program it for a delay start, so that it runs overnight while we’re sleeping. This morning, the clean light was flashing, and the dishes were still wet – like it didn’t go through the heated dry cycle that I always use. I cannot start it on any cycle, and when I hit the cancel button it runs for 2 minutes (not sure what it’s doing, though). The clean light flashes 7 times, then stops for a few seconds, then flashes again for 7 times, etc.

I have a duet front loading washer. it 7 years old. the control lock light is lit up. I can’t get the machine to start.

I have a Whirlpool Gold Quiet Partner III and the Control Lock (press & hold) light is on and it will not let me run a cycle. How do I turn this off and use my dishwasher again?

Where are the fuses for my whirlpool gold quiet wash plus dishwasher located and how to I access them? thank you!

My whirlpool gold quiet partner keypad is locked. I held the air dry button for 5 seconds and it will not unlock. Pleasr help

I have a Kenmore front loading washer, about 8 yrs old, that has had what sounds like occasional bearing noise lately during the spin cycle. Today during the final high speed spin there was a bang and the drum slowed right down. I think it broke something… could this be related to the bearings? When I turned the machine off the drum didn’t seem to have a problem rotating back & forth very slowly for a while like it usually does at the end of a spin. If it is the drum bearings is it an expensive repair? — if it is I’m wondering if I’d be better off getting a new washer.