Repair Help

Hello. I have been bombarded with fridge calls, and I dislike most “modern ” fridges. My customer has a KitchenAid fridge. The fridge works, but the display panel is out. Not lit up. She has no control of the temperatures. I did some internet research and believe that the display board is bad. Is there a way to determine so? Why is it when it comes to any board, I feel helpless? Is it a guessing game when it comes to determining gourds? Other than burn marks that are obvious.
Thanks Bob

I have an Amana Side by side that is not cooling the fans are working and the compressor kicks on and off but it nevers stays on more than about 10 seconds. I have applied a 3 in 1 supco hard start and replaces the defrost timer. what next

This is a frigidaire Icemaker . It makes way to much ice. Do you know if frigidaire makes a extension so the bail arm touches the ice sooner so it makes less ice and over fills bucket. Thank you.

wont complete cycle, says too many suds

The washer will flash a ND code then stop running. I know it means no drain. I have checked all hoses for kinks and debris, and the impeller look good on the pump. The machine is very random when it decides to do this. Is this possibly a pump that is overheating, or is there something else I should be looking for?

This model has a metal hub on the shaft with six screws. When pulling up on the shaft it seems to bottom out. When you look at top of shaft there is a rubber seal and steel ring which doesn’t allow it to come out when we pull up on inner tub. The metal hub will not separate from the basket. When we put removal tool on to pry out it didn’t budge and are afraid of breaking it. Every video we watch shows guys just picking inner tub out or removing with a removal tool. Neither one works for us. Goal is to get inner tub out so we can remove debris etc out from between inner and outer tub. Is this tub just being stubborn or do we need to remove something from the bottom side?

My Kenmore freezer is not cooing properly.

My Maytag washer is not agitating properly and is making a loud noise during the agitation process.

My Maytag dryer is making a loud noise and is also giving off a burning smell.

My electric Kenmore dryer is not heating. Any suggestions?

The turntable on my Kenmore microwave will not move.

My Maytag dishwasher is leaking water.

My Amana washer has no cold water into unit.

My GE dryer is not tumbling, any suggestions?

My Frigidaire dryer is displaying a “LOC” error code and wont do anything else.

My Maytag dryer is making a humming noise and will not start.

My Frigidaire refrigerator is leaking water underneath.

Amana refrigerator not cooling found evaportor fan motor not running check voltage at fan 53 volts present check heater/TS all good, replace TS anyway ran refri 15 minutes to loud TS to close still 53 Volts. If I replace one volt meter lead on fan terminal and the other lead to ground on refri body getting 120 volts. No tech sheet, can someone help with inform or tech sheet. Thanks

My GE refrigerator is not cooling properly and has ice building up in the bottom of the freezer section.

My Maytag dryer heats for a short period of time and then quits.

My Whirlpool washer is making loud grinding noises, any suggestions?

customer says fridge use to start when she tapped between the controls and now nothing happens

The customer called after he changed water valve and dispenser actuator. He said that it showed a eo2 and fo8. When I went there the machine will start lock door and tub will start turning. The whole time it is running the dispenser actuator is turning and never stops. It just turns and turns and doesn’t stop at a place to take on water. Any help would be greatly appreciated .

Customer says this unit does not spin or drain water out

Machine was dead. Changed ccu. Panel lights up and responds but shuts off after 5 seconds. No water enters and dispenser doesn’t move. Will work in drain and spin

Have an odd one here. display on touch pad goes dead after a few weeks. unplug unit and it restores normal operation, been out 2 times and unplugged and came back on. I don’t want to just throw parts at this, anyone see this before or have any suggestions. Thanks in advance

Hi Guys,
Have a SAMSUNG REFRIGERATOR Need to get the faceplate off the dispenser but do not see any hooks, latches or screws.
Anybody have a manual to share with the instructions.

Went on job Amana refrigerator not cooling found evaporator fan motor not running check voltage at fan 53 volts check heater and T S all good, replace T S. ran refrigerator 15 minutes to aloud T S to close still 50 volts no tech sheet can someone help. If place one volt meter lead on fan motor terminal and other lead to ground on refrigerator body getting 120 volts. Can someone help.