Repair Help

hello, i have change the shifter Actuator on my whirlpool washer and did the diagnostic test on it and now it is showing sensing. what do i need to do now?

Dw seems to be stuck in wash mode, Couldn’t make heads or tails of diagnostic mode. In light wash I got the dispenser to open but never heard a drain cycle after the prewash, I may have just missed it as I was going over tech sheet in library. Unit seems to pause for a few seconds and then go back in to wash mode. pushed canel drain 45 min in.lw cycle should last a total of 25 min max according to tech sheet. HO states wash times exceeding 4 hrs, that will only stop if terminated. the unit appears to have a pressure switch for soil sensing,wondering if this could cause this problem. Any thoughts folks?

the power failure alarm was on. could not turn it off the alarm on the door control because nothing was working. i unpluged and pluged it now the refrigerator comes on for couple second and goes off and does not stay on. it goes off an on what do i need to change to fix this problem

How to diagnose.

TEST MODE

Need Error codes & diagnostics for Samsung dryer

LG parts

I need to find parts for Verona through Eurochef. Any help will be greatly appreciated

I saw a nice video on load at spin washer video where the Drive Block tab where gone , my seen good but I have the same load and banging vibration at spin when is goes full speed , like the video, what do you think can the block be the problem anyway it woks fine other wise, just load spin LIKE THE VIDEO.

I have maytag dryer: 6800AWW
I saw the ignitor is on and the flame is on for less than 1 minute, the go down. Then later flames come back again for less than 1 minute, then go down again.
Is this the issue with valve coil?
(I already changed the High limit thermostat, ignitor, and thermal fuse but problem still there)

Paul

Hello, I was directed here from youtube to ask a question.
All of a sudden my waseher does not start at all,whether to fill,agitate or spin. I checked the power source,all is fine with my house. I was thinking it maybe overheated,but it still does not start.Then maybe I thought it might be a lid lock switch,although when it worked it dispensed water with the lid opened. Will that switch determine if washer starts at all?
Any help is greatly appreciated.

This is actually a series made by Whirlpool 810-811. The motor is not running and water doesn’t drain. However, the board will still go thru its cycles as if it is working properly. Is there a reset button somewhere on this unit to start the motor? This is a 12 year unit which I’ve probably used half a dozen times.

What recommendations can you provide as I’m a DIY’er?

Model number LFX25991ST/06 What position is the refrigerant valve in when the refrigerator is unplugged? I want to pull a vacuum and I know the Whirlpool you have to use diagnostic mode to open the 3-way valve. Is that the case with
the LG?

Does anyone know of a parts store that does not have a core charge on boards? Please share…Thanks

bosch dishwasher model she6at05ucx/o5
error cod e64
we replaced the control board to no avail
need some assitance please we belieive it could be heating system , also
how do you get this dishwasher into test mode

washer fills, agitates, drains, spins, fills for rinse, stops.

Having a problem removing the icemaker on thid box. model GI6FDRXXY03
Wire harness cover comes off and latch holding icemaker in moved easily but the icemaker will not move.

Anyone have a manual on this frig.

There is a sturdy piece of plastic where i though the grommet should be and i am afraid to pull it out because i might break it.

Every time i open the door and all throughout the day i here a noise that sounds like a pump trying to cut on. I have opened the door and it sounds like it is water or something trying to come through the lines where there is a container of some sort back behind the drawer and behind a cover. It looks like a water bottle. I don’t think this should be coming on all the time. Any help would be great.

Complaint: Unit taking very long time to complete cycle and or pauses with water,
but will complete cycle. This unit is located in a Seminary with multiple users so can’t get proper feedback. Any help appreciated.

It seems that the only part number I see coming up for a p-trap drain kit is “W10619951”. In the video, it says there is a different kit for a fridge with 30″ doors, and ones with 33″-36″ doors. How do I know which part to get? I cannot find any place that clearly states which part number is for which size doors. Any help is appreciated. Thanks.

Model-GZ25FSRXYY2
Serial-K22419304
Ice maker when I removed it had a full/frozen fill cup, ejector arm at 5 o’clock stuck at little ice bits. Cleared, installed, put power to. unit advanced to freeze position but gave no ice after 5hrs. Where would you guys point me on this critter? Ice maker in frig section. freezer is cold enough.
Thanks,

We have a very strange problem with this washer, Whirlpool ,mod.WFW8400TW00
It leaks in the clean cycle only . Couldn’t find the source of the leak
because dryer is on the top of the washing machine ,located in the very small room .
Anyone knows about the source of the leak in the clean cycle so we can save our time
without going back and forth ?
Thank you

Circuit to radiant sensor was reading closed when this was accruing, installed a new sensor for trial, reinstalled original sensor, unit is now working properly after board replacement on both units. Customer was flipping out as you would imagine and had gas company involved etc. Very disconcerting when you have this much raw gas going into a dryer, may have been a different outcome with a restricted vent or venting with a leak in it.
Assumption that flame detector = Radiant sensor?

looking for nla clock 4342969 for roper range d9757^6

I have a customer with a Maytag Gas Range, MGR7775WS 2, R10414233. This unit doesn’t have an ignitor but has a spark mule for the lower oven and it doesn’t always light on the first try. Is this something to worry about and is there anything that can be done about it?

experiencing frequent Unbalanced Load error codes from her Samsung top load washer, model wa476dshawr/a1. The unit is firm on the floor and level. The error occurs regardless of the load size or type. Does anyone have any suggestions?

We need some advice on a Whirlpool washer WTW4910XQ0.
When the unit is running the belt keeps sliding down and coming off.
Any advice would be appreciated.