Repair Help

The original complaint was that this Dishwasher was not responding to anything. NO POWER whatsoever. So we replaced the main control board and now the dishwasher will turn on but it the display keeps Flashing and not responding to anything. We have reset this board multiple times but it doesn’t seem to help. Does this unit need to have the control board be programmed or could this board be faulty?

Ge washer GTW330ask4ww. water inlet valve turns on and off intermittently then stops all together. Tank only fills up less than a gallon. Checked for error codes and I get code 5. XML version non-critical.

This washer machine does not power on any more. I would like to know what parts besides the PCB main board would help solve this problem. Please provide part numbers and diagram of the washer. Does this washer have a noise filter that can solve this problem. Any advice would be help full. They only thing tried was changing the power cord which worked for a few washes before no longer powering on. This is a Samsung washer.

Costumer explained Dryer door opens during operation. I ran the dryer and the door never opened.

Already checked and tested power, fuses, magnetron, capacitor and wiring harness for damage.

The washer turns on and goes through the washing cycle. It drains the watet after rinse. But fails to go into spin mode.

When you press bake to preheat upper oven broil element stays on.
When you press bake to preheat lower oven Broil element does not come on only bake element

I need service manuel to change out relay board

the refrigerator side stays at the set temperature, but the freezer side doesn’t go lower then 41 degrees I have the setting at 5 degrees.

This is a coin operated electric dryer. When it is started, the minutes display shows 45 and the light on the top panel is on for “cooling down” instead of “drying”. The heat cycles on and off and the time display counts down normally to 1 minute and remains at 1 minute, and the dryer continues to run and heat and doesn’t shut off. I’m suspecting the timer is the issue. Any assistance would be appreciated.
Thank you.

the programming starts normally, water and washing works, when it is on the programming to drain the water the pump does not turn off and shows error I30, I have already replaced the board and the same defect continues

Machine not powering on

I Keep getting smart auto and heavy lights blinking after the dishwasher is running maybe five minutes, It seems like when it starts it automatically drains. I’ve reset the dishwasher multiple times each time it allows the psycho to go a little bit further but it doesn’t look like it’s putting much water in the dishwasher.

Last week I noticed the clock starting losing time. Then both timers stopped counting down when set. Now the interior lights don’t go on when the door is opened. So far, burners and oven work fine.

If you open the following link, that is the noise being made during agitation: https://www.youtube.com/watch?v=WvDDGzhkHu0 . I have removed the Rotor motor and found that at some point, a small amount of water made it’s way to the Rotor Motor as I could see water streaks formed as the motor spun, at speed. Never saw any water on the floor beneath the Washing Machine. I had the Agitator removed at the same time, and found no substantial movement in the shaft at top or bottom. No wear to the splines in the agitator/Impeller or Impeller Insert. The teeth on the Mode Shifter showed some very minor wear. No visible damage to either the Stator or Rotor Motor. Is there a most likely failed part causing the noise or a way to test to find the failed or failing part. My research so far has suggested any of the above mentioned parts as well as the DSM Module. FYI: in searching parts, the Bearing Assy shows as not available. I had GE Parts do some research and the new part # is WH38x24734..Please advise.

We smelled burning rubber the last few times we used our washer. Now the agitator spins wildly (out of control) while the drum starts to move, but then both shut down. It seems the machine is trying to start the drain/spin cycle, but can’t. It attempts to start the cycle, but the sequence described above repeats and the machine eventually shuts down. Having repaired this machine a few times in the past, I inspected the belt, which shows no visible signs of damage. With the belt attached, I turned the splutch wheel and I noticed what I would describe as a slip inside the motor.

Please help me figure out what I need to fix this.
Thank you in advance for your help!

-B.J.

This washer is brand new i have looked at the info it came with is says if 888 flashed its the flow meter or the harness and i have replaced the flow meter still the same result

Need a service manual & wiring diagram along with error codes .
Thanks

See above. Newer model Samsung French Door refrigerator. Display is on the right hand side on interior of refrigerator. Above “Fridge” button flashes the letter C. Above the “Freezer” button flashes 40, 24, 25, and 65. Unit appears to be maintaining temp however it will intermittently trip the breaker. We have replaced main control board already.

OK WELL THIS SAM WASHER IS NOT SPINING REPLACED THE ROTOR POSITION SENSOR AND STILL NOTHING AND WHEN DOING A DIAGNOSTIC CODE CHECK ITS GIVING ME A (AE6) & (DE) ERROR CODE THE WATER AND EVERITHING AND IT DRAINS JUST WONT SPIN I DONT HEAR A MOTOR HUMING OR ANYTHING

When cycle start water fills up and drain as intended but tub not turning.

Most is the control panel works fine except for the Normal Wash and Heavy Wash options on the right side.

Those two options will not light up at all.
No matter what other options or settings I press I can’t get those two buttons to change, work or even turn on at all.