1 vote
2k views
1 vote
2k views

For this kind of problem, do we need clips only for this problem or we have to worry about the ICe Maker and argue motor replacement? Thank you.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Washer will go all the way through the cycle, will drain but will not spin.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

My GE dryer is very loud.

0 votes
3k views

I can get ice ice if I open door and hit ice button but not on door.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

need help troubleshooting issue with samsungs refrigerator with dual zones. frige side kkep frezing and not cooling .
checked heater and by metal and they are ok. fan also since to be running but after a couple days the evap will frezze againg and it will stop working.
i have had this issue on a couple of samsung units.

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

water presssure switch working but always 120 on the wire for no o water switch. dont have any diagram or nothing to follow.
motor controller board changed already but still not working

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

Have already taken the basket, but hearing some cracking noise, when its in the agitation stage.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
7k views

it started by squeaking alot. repair guy’s solution: spray wd 40 and saying “see, it’s not sqeaking now”. $75.00 that cost me. within a month noise was back. took it apart. drum roller on right side ground down the little fiber washer but was moving ok. I replaced both drum rollers and washers of course and the damn belt pulley also. worked for a while then eventually started making a grinding noise…due to the the drum hitting the front cowling or whatever it’s called. find metal filings at bottom in front. I replaced the guides (the blue and cork ones) worked well for a while and now it’s grinding again. I can reach inside the machine and lift the drum in front and it moves 1/2 to 1 inch when I push toward the ceiling. I need to figure out how to keep the drum from tilting down in front. I thought of wedging something small under the guides in front to raise them up but don’t know if it would create enough lift to get the drum off of the part it’s grinding on. Any bright ideas are most welcome….other than “get a new dryer”

Allan Tomson

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Sometimes the dryer heat it up. But most case, there is no heat in the drum. We are not sure it is gas valve, or igniter. Thank you.

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
3k views

GRIDDLE IGNITER WONT LIGHT
REPLACED IGNITER AND SWITCH

STILL – IGNITER DOESNT GET 120 BETWEEN 2 WIRES

WHAT TO REPLACE NEXT?

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
4k views

The units evaporator was frozen. I cleaned evap and replaced the adc control. It had the old 1st generation so i replaced the new wiring for the orange adc now the damper is running all the time. I did notice the fresh food thermostat had three wires new wiring harness has two. When i installed i had the freezer thermostat off. first i turn the fresh thermo on fan came on and damper, then i turn fresh food control off fan turn off just like it is supposed and the damper motor kept running

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

No start at all

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
3k views

No turn on the top right and bottom right Burner

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

Looking at a samsung microwave that is dead. The fuses, t-stats and door switches are all ok.

No wiring diagram. Looking for a wiring diagram and service manual.

Thanks

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
7k views

Somebody already replaced the main control board and the power board but the error keeps coming back Can you guys pull me in the direction of a resolution and also can I get some diagnostic manual’s please

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

the top oven works fine .the lower oven the heating element will get hot on any temp including bake or broil or roast. the element will not heat up. do you have ant instructions on this unit thanks

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Where can I find parts for this dishwasher? I found the filter screens torn and the macerater blade is loose on the shaft and the screen is stopped up, but I can’t find that blade and screen.
Is there a manual for this?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
3k views

I have a unit to repair that has a defective key mechanism. I took it apart and am not sure of the reassembly of washers, spacers and parts. I need a diagram and parts list.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Need a wiring diagram for this product please

  • dwoods asked 8 years ago
  • last active 8 years ago
0 votes
4k views

2 YEAR OLD LG RFG, LARGE BALL OF ICE BUILDUP BETWEEN EVAPORATOR MOTOR AND ICE MAKER FAN MOTOR
(CAUSING NOISE). I WAS WONDERING IF THERE ARE ANY SERVICE UPDATES FOR SUCH A PROBLEM (I.E.
AIRFLOW CHANGE).

THE CUSTOMER SAID IT IS POSSBILE THAT THE FREEZER DOOR DOESN’T ALWAYS GET SHUT, WHICH COULD CAUSE SUCH A PROBLEM. i JUST WANTED TO MAKE SURE THIS ISN’S A COMMON ISSUE.

THANKS!

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
9k views

Hello my question today is with the Samsung dryer looks like it’s the dual element style will run for 3-5 seconds and then shut off. If the power is turned off and restarted on the unit it would start again for another 3-5 seconds and then shut off but if it’s press to start without powering off the unit it will not start again unless it’s powered off. This seems to happen in any mode whether it’s timed or auto. The unit is only about two years old I don’t think it’s running long enough for that motor to even overheat within 3-5 seconds also the unit is that even running long enough to even start to warm up in the 3 to 5 second window.

I would just like to know what to suspect at this point? To check the relay on the board to see if it’s open or is this a known issue ? I have not seen the Samsung dryer do this before

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
4k views

Order the Module, dispenser – part 242074204 which they substitute with part 24074216. The part looks a little different but the big issue is the wiring harness is totally different. So what do you do with a part like this?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

How do you put into forced defrost mode and which board (ui assy in fresh food section, or electronic control near compressor) controls defrost? (mini service manual missing)

  • joeski1369 asked 8 years ago
  • last active 8 years ago
0 votes
2k views

WASHER DOES MAKES A LIGHT KNOCKING SOUND DURING WASH CYCLE.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
16k views

MACHINE DOES WORKS. DISPLAY “AF” ERROR CODE.ELECTRIC DRYER.

  • Guest asked 8 years ago
  • last active 8 years ago
1 vote
2k views

MACHINE DOES NOTHING, WHEN YOU TURN ON.

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
2k views

Is the freezer fan the only way fresh food is chilled?

  • Guest asked 8 years ago
  • last active 8 years ago
0 votes
4k views

I watched this video and was able to disassemble the dishwasher, clean the parts, and reassemble most of it. https://www.youtube.com/watch?v=VtRWr78dbJc
However, when I try to reattach the bottom spray arm, the part that should screw in tightly to secure to bottom arm will not fit in securely. So the bottom spray arm just sits on the tube and wiggles. I can get the part to secure tightly to spray arm by tightening it counter clockwise but not to the tube.

Thank you.

  • Guest asked 8 years ago
  • last active 8 years ago
Showing 3181 - 3210 of 9k results