0 votes
2k views

The dishwasher leaks from the bottom near the pump when it goes into the drain cycle
And there is no pressure to reach the top as well

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Customer brought washer said was not draining properly. When we tried washer made humming sound lid lock kicks in and out then no water comes in and nothing happens. lid switch light stays flickering

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Dispenser will only work in test mode. All parts check out fine

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Water dispenser don’t work. This is located inside refrigerator on left hand wall. When paddle push, nothing. No noises. Thanks in advance

0 votes
3k views

We have a Whirlpool dishwasher, above model, runs to about 1/2 way thru cycle and shuts off, cancel drain light blinks continuously. Any help/ advice we can get with this unit would be appreciated.
Thanks in advance

0 votes
4k views
  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Maytag washer setting the Know on Drain/Spin, the motor runs slow and is getting so hot.
have you run into that problem before.?

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
4k views

My question is that on this frigidaire french door refrigerator the icemaker in the refrigerator part the thermister attached to the icemaker underneath is reaped off by the ice when the auger is activated as far as i can see. Is there a way to reduce the production of ice on this unit, or is there another type of icemaker to replace the flextray? I have done two so far with this problem, this time the fridge is giving a sy cf error code the icemaker has the thermister torn and this error code calls for replacing the control board and the U/I but i saw where if by replacing the icemaker first the errior code might go away and not have to replace the boards?

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
4k views

customer brought washer in and complains that when unit is at the rinse cycle it will stop an d thats it. I thought the temp switch was the culprit pt number w101u84148 but i dont know how to check the pt with my meter.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

My customer called me about his Samsung ice maker. He said that it worked well ever since he owned it. Then suddenly it just stopped making ice. I tried to reset it, but no luck. The water works fine, just not producing ice.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
4k views

step by step procedure to do a diagnostic test?

Alex

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Whenever I turned on the breaker trips, just that soon. Frigadaire

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
4k views

Homeowner stated washer give code last night and the opened and shut door and the washer worked just fine. Today trying to run a cycle the washer is dead, nothing will happen at all, no lights, no nothing. Of course they don’t remember what the code given was. Anything other than a control board issue here?

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Microwave has no power no digital read out.

Panasonic is the brand name

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
4k views

Hello, I love your new website.
My customer has a GE French Door fridge with the freezer on the bottom. I think the board that controls the fans is bad. I am the forth technician to service this fridge. She has had nothing but problems with it since she bought it. A year after, GE replaced the compressor. After that 3 boards were replaced. And more! Now this?..

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views
  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

This unit does not have a water dispenser. The line for the icemaker keeps freezing up, stopping flow to icemaker.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Initially I replaced the drain pump and heating element due to the 7flash error/unit not starting indicating a heating issue. Worked for a week, then replaced the main control board, and tstat. Ran for about a
Month. The water coming into the unit takes forever to heat, I understand that this unit senses water temp and will throw an error if the water temp is not right. Is there another part I need to replace or ????

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views
  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

The cycle ended .
As wife was takeing the load out the light went off.
And now the whef we press the start button the lights in the front go on but will not start.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

I’m trying to find a trouble shooting and repair video for this model!

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

I got a no freezing condition and I wanna check the evaporator fan motor. I got a chance to take the freezer cover off and I didn’t see it running.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

ihave a whirpool duet steam washer changed pressure sensor still f 35 pump is fine pressure tube is clear

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
15k views

I cannot get the ice maker to function into harvest cycle. I need help with diagnostics.

0 votes
4k views

Unit not cooling. Checked compressor relay/overload-Ok. Maybe board and thermister? Any help is appreciated.

0 votes
3k views

Customer issue was ice maker in refri section was froze up, so he took a hair dryer to melt the ice, after finsh there a funny smell and refri stop cooling, on my arrival check the icemaker section their is a bad odor plus a sound like water siphon. Check the rest of the refri everything seem normal, but no coolng compressor amp draw one point 1.75, but the discharge line a little warm, suction cold, my thought low charge.Will be going back tomorrow, does anyone have information on this one. thanks in advance

0 votes
3k views

we repaired in November for no cool or freeze.now 3 months later now complaint freezing in fresh food,evaperator is iceing up

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views

Two weeks agp the oven would shut off in the middle of baking, and now it doesn.t even  start to bake.
Thank u.

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
4k views

Need service manual. Wonder if the freezer door SW controls the evaporator fan, light and something else?

Alex

  • Guest asked 10 years ago
  • last active 10 years ago
0 votes
3k views
  • Guest asked 10 years ago
  • last active 10 years ago
Showing 7111 - 7140 of 9k results