Repair Help

I am trying to replace the touchscreen control board on my refrigerator. I need to know how to remove the display panel to get to the board. Looking for help or a video to show me how to remove the touchpad to get to the control board. This is a Samsung French door four-door refrigerator not a side-by-side.

Frigidaire model#GLFH21F8HWE

Looking for a list of diagnostic codes for my GE fridge.
Not sure my freezer heater works and want to run a test. And also test the thermistors.
So need tech sheet or service manual for my specific fridge.

Attempted to rewrite control board after compressor replacement only getting failure from jig after attempting rewrite

Is there any videos or do you have any instructions on how to remove the wash basin the part that’s underneath the lid as the 2020 model does not seem to have the screws on the side to detach the lid. Part that needs to be replace is DC61-04129A along with part DC97-20069A. Please advise on how this can be done. Thank you.

I wanted try to fix Ge fridge video on repair for beginners

Machine starts and trying to fill but won’t

This unit has a failed compressor and it states we have to update the board on this unit. Do you have any instructional materials, or guides on how to complete this common LG compressor repair. Kenmore Refrigerator – LG BUILT

Washer Lid Assembly will not stay open when lifted any ideal of what parts would fix issue to hold lid up when filling washer. Looking for more detail that is better than the Spring Hinge which is hard to remove. Looking for more insight on what could be causing this problem and any detail breakdown of how to go about repair. Any videos on this type of washer with similar lid staying in place would be helpful or how to replace the lid assembly. Mainly happens when the under lid is corrected that’s when it falls down and will not stay up in place. Thanks.

Leaving clothes wet after cycle

I have this frig I’m really lost on ran the diagnostics says there a short in the defrost system.But the weird thing is both evaporators are frozen up frig and freezer.Would this be a control board problem.please help I’m in the hole on this one thanks Jim

You have to manually advance in different cycles

Bottom icemaker not working. Fridge runs great and upper icemaker in door works great. Have replaced main control board (unrelated to icemaker), 2 different icemakers, and a water valve. Icemaker won’t even turn fingers to flip out ice. I put a bit of water in the icemaker to see if it was valve or icemaker and still no ice flipped out.

Need to resolve ASAP because fridge is taking up space at store and can’t be sold until icemaker issue is sorted.

Need to know how to dissemble icemaker compartment to install evaporator Kit 5303918444.

No matter where the control is set it freezes every thing.
How do I test this unit?
I need a service manual and tech sheet and any advice you can give

I have a Samsung top loading washer model WA52M7750AV. When plugged in I can hear a relay click, and when I hit the power button I hear another relay click, but get nothing on the display boards.

While the power is connected on green led on the system board flashes every 3 seconds regardless if the power button has been pressed
Another led on the system board flashes 3 times after the power button is pressed and then never again.

Is the system board bad, or is one or both of the display/input boards bad?

Brian

Hi,
I am troubleshooting a no LED light issue on this unit, All the LEDs work except the 5 on the roof of the refrigerator. The schematic shows that the 5 fridge roof LED’s are divided into 2 series circuits, 3 in one series and 2 in the other going back to the LED Driver board for the DC source. Both of these strings are not working, I have diagnosed that the LED Driver board is partially defective .

The problem is, it is not shown in any service literature, ANYWHERE. The visual shows it is located next to the control board along with the power supply, The only part shown in the exploded diagram is the Control board itself, Whirlpool W11161172. If you do a parts list search for LED Driver, it does not generate any hits. I am at a loss, I have check multiple sources including the Factory SM with no luck.

I need the part number for the LED Driver Board! Why is it not shown or listed anywhere? I wasted 2 hours looking!!!

Thanks 🙂
Tom
609 418 0278

There is a grinding noise during agitation. I have cycled through the service mode and in agitation cycle there is grinding noise.

What part or parts do I need to order to fix this before it becomes a bigger problem.

Thanks

I recieving an error code F dy and cannot find what it means or is referring to

Fridge has power, compressor running, condenser fan running, lights and front controls work. No cooling in fridge or freezer. Evaporator fans not running. Suction and discharge lines are not hot or cold. Fridge is new but just stopped cooling. Not sure what to do next. Any suggestions would be greatly appreciated

Finding plastic pieces in tub when cycle is finished. Took agitator out, looks ok, no pieces come from it. Seems as if inner tub has a little play in it. This may be causing the excessive shaking. I don’t see any pieces broke off of top cover. I would say that’s where the pieces are coming from. The washer is only 3yrs old. have there been issues with loose parts or suspension troubles, or balance problems???? Put the washer in spin with no clothes in it, and it was shaking too much, and did bang slightly.

While trying to heat over, a low bang noise then no gas. No gas at stove top and no oven. Is this some kind of safety shut down. Or is this a problem at.the.propane tank?

went to back of range element tested bad, removed the 4 screws seperated the insulation tried pull in on the element and it move back a inch or so, i know it has slide tabs in front on the bar. is there a release that im missing or do you have to give it a good pull and lift up or down. im at a cross roads

thanks

al
7722631578

Washer stops mid cycle with a load in but complete cycle without a load.

The display will change almost by the minute.
It can be programmed and used but after several hours it will lock up and has to be unplugged and rebooted then repeat the process.
One time the microwave came on on its own
Sometimes it will go into the service mode by itself. But the in a few minutes will go away.

At times it will go completely blank.
Can this be the harness in the door.

I need a tech sheet and service manual and service bulletins.
I see this is an issue with this model.

There is a lot of Frost BUILDING UP INSIDE THE REFRIGERATOR BEHIND THE PANEL BEHIND THE CRISPERS. What do you think could cause this?

the fridge is around 25 Fahrenheit set on low

HAVE TROUBLE PUTTING IN DIAGNOSTICS OR WHOEVER WROTE THIS MISSED A STEP FRIDGE IS TO COLD CANT
FIND A VIDEO ON THE SITE OF PREMIUM my email is garth@saparas.com

Hello, The temperature in the Freezer & Fresh food section are ok. Zero & 37. The dividing wall between Freezer & Fresh food is sweating, causing condensation to drip down in the Fresh Food section. This is a Side x Side model. Door gaskets are sealing good. Have any solutions???? Thank You, Jim